To Next PageTo Next PageWhat to do if my Indesit IDL 500 doesn't start?
If your Indesit Dishwasher doesn't start, make sure the plug is properly inserted into the electrical socket and that there is power in the house. Also, check that the dishwasher door is completely shut. Finally, ensure a delayed start hasn't been programmed.
Why are the dishes not clean after using my Indesit Dishwasher?
If your dishes aren't clean after a wash cycle in your Indesit Dishwasher, several factors could be at play. Check that the racks aren't overloaded and that the dishes are arranged properly, allowing the sprayer arms to move freely. Ensure you're using an appropriate wash cycle. Also, verify that you're using the correct amount of detergent and that it's designed for dishwashers. Make sure the lid on the rinse aid compartment is closed correctly, and that the filter isn't dirty or blocked. Finally, check the refined salt level.
What to do if no water drains out from Indesit IDL 500 Dishwasher?
If water isn't draining from your Indesit Dishwasher, first check if the cycle has finished. Then, inspect the water inlet hose for any bends. Also, make sure the drain duct isn't blocked and that the filter isn't clogged with food residues.
Why Indesit IDL 500 Dishwasher doesn't take in water and beeps?
If your Indesit Dishwasher isn't taking in water and is beeping, there may be no water in the mains supply, or the water inlet hose could be bent. Turn on the tap; the appliance should start after a few minutes. If beeps continue, the appliance lock may be activated. Turn the dishwasher off and on, turn on the tap, and after 20 seconds, reprogram and restart the wash cycle.
How to remove white film from dishes in Indesit IDL 500?
To remove white film or limescale from dishes in your Indesit Dishwasher, ensure the refined salt level is adequate and the dosage setting is appropriate for your water hardness. Check that the salt dispenser lid is properly closed. Also, make sure the rinse aid hasn't been used up and the dosage isn't too low. Note that some crockery made from non-stick material may be prone to this issue.
Why is crockery not drying properly in my Indesit IDL 500 Dishwasher?
If your crockery isn't drying properly in your Indesit Dishwasher, ensure that the rinse aid hasn't been used up or that the dosage is too low, and that the rinse aid dispenser setting is high enough. Also, check that you have selected a wash cycle that includes a drying program.
What does it mean when my Indesit IDL 500 shows a foam/blocked filter alarm?
If your Indesit Dishwasher displays a foam/blocked filter alarm, switch off the appliance. This could indicate an excess of foam inside the machine, possibly due to using a detergent not suitable for dishwashers, or the rinse aid compartment lid not being shut correctly. Remove any food residues from the filters, replace the filter assembly correctly, and then switch the machine back on. Reprogram and restart the wash cycle.
Why do dishes have streaks after washing in my Indesit IDL 500?
If your dishes are streaked or have a bluish tinge after washing in your Indesit Dishwasher, the rinse aid dosage might be too high.
Why does my Indesit IDL 500 make excessive noise?
Excessive noise from your Indesit Dishwasher might be caused by dishes rattling against each other or against the sprayer arms.
What to do for Water intake solenoid valve malfunction alarm in Indesit Dishwasher?
If you get a water intake solenoid valve malfunction alarm on your Indesit Dishwasher, switch the appliance off and then back on after a minute. If the alarm persists, shut off the water tap to prevent flooding, remove the plug from the electrical socket, and contact assistance.
General| Type | Freestanding |
|---|---|
| Number of Place Settings | 10 |
| Noise Level | 54 dB |
| Height | 85 cm |
| Width | 45 cm |
| Depth | 60 cm |
| Freestanding | Yes |
| Colour | White |
| Delay Start | Yes |
