Ingersoll-Rand 325 - User Manual

Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
 Ingersoll–Rand Company 2000
Printed in U.S.A.
03533601
Form P6703
Edition 6
April, 2000
INSTRUCTIONS FOR
MODEL 325 AND 325–EU HEAVY DUTY AIR NIBBLER
The 325 and 325–EU Air Nibbler is designed for cutting cold rolled steel, plastic, tin,
aluminum, and other metals in paint and auto body shops and in sheet metal shops.
Ingersoll–Rand is not responsible for customer modification of tools for applications
on which Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
• Always operate, inspect and maintain this tool in
accordance with all regulations (local, state,
federal and country), that may apply to hand
held/hand operated pneumatic tools.
• For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 5/16” (8 mm) inside diameter air supply
hose.
• Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
• Do not use damaged, frayed or deteriorated air
hoses and fittings.
• Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
• Always use clean, dry air at 90 psig (6.2 bar/
620 kPa) maximum air pressure. Dust, corrosive
fumes and/or excessive moisture can ruin the
motor of an air tool.
• Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
• Do not remove any labels. Replace any damaged
label.
USING THE TOOL
• Always wear eye protection when operating or
performing maintenance on this tool.
• Always wear hearing protection when operating
this tool.
• Keep hands, loose clothing and long hair away
from blades when operating this cutter.
• Blades may continue to cut briefly after throttle is
released.
• Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
• Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended
air pressure.
• Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using
any tool if discomfort, tingling feeling or pain
occurs. Seek medical advice before resuming use.
• Use accessories recommended by Ingersoll–Rand.
• This tool is not designed for working in explosive
atmospheres.
• This tool is not insulated against electric shock.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized
Servicenter.
GB

Summary

Placing Tool in Service

Operational and Maintenance Compliance

Adherence to regulations, optimal air pressure, hose integrity, and disconnection for safe operation and maintenance.

Safe Handling and Operation Practices

Guidelines for safe tool use, including PPE, keeping clear of moving parts, body stance, and anticipating tool behavior.

Ergonomics and Tool Limitations

Addresses vibration effects, user comfort, recommended accessories, and limitations for explosive atmospheres or electrical insulation.

Safety Warnings and Label Identification

Critical Safety Warnings

Key warnings for safe operation, covering eye/hearing protection, handling, air supply, and vibration-related risks.

Placing Tool in Service - Lubrication

Lubrication and Air System Setup

Instructions for using air line lubricators and specific oils, and maintaining the air system for tool longevity.

Specifications

Maintenance Instructions

Part Number Ordering Reference

Reference guide for ordering specific replacement parts using their corresponding part numbers.

Service Centers

Ingersoll-Rand 325 Specifications

General

Brand	Ingersoll-Rand
Model	325
Category	Impact Driver
Language	English