EasyManua.ls Logo

Ingersoll-Rand 9115 - User Manual

Ingersoll-Rand 9115
20 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Form P7744
Edition 1
December, 2003
CCN 04580668
INSTRUCTIONS FOR
MODEL 9115
HVLP GRAVITY FEED SPRAYER
Model 9115 Sprayer is designed for paint, lacquer, stain or other finish type material.
• IMPORTANT SAFETY INFORMATION ENCLOSED - SAVE THESE INSTRUCTIONS
• READ AND UNDERSTAND THIS MANUAL BEFORE OPERATING THIS PRODUCT
• IT IS YOUR RESPONSIBILITY TO MAKE THIS SAFETY INFORMATION
AVAILABLE TO OTHERS THAT WILL OPERATE THIS PRODUCT
• FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY
PLACING THE PAINT SPRAYER IN SERVICE
• Always install, operate, inspect and
maintain this product in accordance with
all applicable standards and regulations
(local, state, country, federal, etc.).
• Always use clean, dry air at 43 psig
maximum air pressure at the inlet. Higher
pressure may result in hazardous
situations.
• Be sure all hoses and fittings are the
correct size and are tightly secured. See
Dwg. TPD905-2a for a typical piping
arrangement.
• Ensure an accessible emergency shut off
valve has been installed in the air supply
line, and make others aware of its location.
• Do not use damaged, frayed or
deteriorated air hoses and fittings.
• Keep clear of whipping air hoses. Shut off
the compressed air before approaching a
whipping hose.
• Always turn off the air supply, bleed the air
pressure and disconnect the air supply
hose before installing, removing or
adjusting any accessory on this product, or
before performing any maintenance on
this product or any accessory.
• Do not lubricate products with flammable
or volatile liquids such as kerosene, diesel
or jet fuel. Use only recommended
lubricants.
• Use only proper cleaning solvents to clean
parts. Use only cleaning solvents which
meet current safety and health standards.
Use cleaning solvents in a well ventilated
area.
• Keep work area clean, uncluttered,
ventilated and illuminated.
• Do not remove any labels. Replace any
damaged label.
USING THE PAINT SPRAYER
• Always wear eye protection when operating
or performing maintenance on this
product.
• Always use Personal Protective Equipment
appropriate to the product used and
material worked. This may include dust
mask or other breathing apparatus, safety
glasses, ear plugs, gloves, apron, safety
shoes, hard hat and other equipment.
• When wearing gloves always be sure that
the gloves will not prevent the controls
from being operated.
• Keep others a safe distance from your
work area, or ensure they use appropriate
Personal Protective Equipment.
• This product is not insulated against
electric shock.
• Do not point the spray gun at anyone or
any part of the body.
• Do not stop or deflect spray with your
hand, body, glove, or rag.
• Repetitive motions or uncomfortable
positions may be harmful to your hands
and arms. Stop using any product if
discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
• Keep body stance balanced and firm. Do
not overreach when operating this
product.
• To avoid accidental starting - ensure
product is in "off" position before applying
power, avoid throttle when carrying, and
release throttle with loss of air.
• Do not carry or drag this product by the
hose.
• Do not use this product when tired, or
under the influence of medication, drugs,
or alcohol.
Refer All Communications to the Nearest
Ingersoll-Rand Office or Distributor.
© Ingersoll-Rand Company 2003
Printed in Taiwan
FR
ES

Questions and Answers

  • A
    Alicia GuzmanAug 1, 2025
    Why is there excessive overspray from my Ingersoll-Rand Paint Sprayer?
    • A
      Alexander ProctorAug 1, 2025
      Excessive overspray can occur if the atomization pressure is too high or if the spray gun is moved improperly. To resolve this, reduce the air pressure and move the gun parallel to the surface at a moderate pace.
  • E
    erik43Aug 5, 2025
    What to do if my Ingersoll-Rand 9115 Paint Sprayer has a split spray pattern?
    • A
      alexabrownAug 6, 2025
      A split spray pattern can occur if the atomization air pressure is too high, the fluid flow is too low, or the fan pattern is open too far. To fix this, reduce the air pressure, turn the fluid control knob counterclockwise to increase flow, and turn the pattern control knob clockwise to reduce fan width.
  • E
    Edward PrinceAug 10, 2025
    How to fix an Ingersoll-Rand Paint Sprayer that will not spray?
    • M
      Melody WongAug 10, 2025
      If the paint sprayer will not spray, it could be due to no pressure at the gun or a closed fluid control. Check the air lines to ensure there is pressure and turn the fluid control counterclockwise to open it.
  • R
    rreeseAug 14, 2025
    Why does my Ingersoll-Rand 9115 Paint Sprayer have a center heavy spray pattern?
    • C
      Cory BryanAug 14, 2025
      A center heavy spray pattern may occur if the fluid is too thick or the atomization air pressure is too low. To correct this, thin the fluid and increase the air pressure.
  • J
    Jonathan CarrollAug 19, 2025
    What to do if my Ingersoll-Rand 9115 has a fluttering spray?
    • D
      Daniel WilsonAug 19, 2025
      A fluttering spray can be caused by a low fluid level, a loose or damaged fluid inlet connection, or a plugged vent hole in the container. Refill the fluid, tighten or replace the fluid inlet connection, and clean the vent hole.
  • E
    Erica SnyderAug 23, 2025
    Why does my Ingersoll-Rand 9115 have a top or bottom heavy spray pattern?
    • Z
      Zachary TerryAug 23, 2025
      A top or bottom heavy spray pattern can be caused by debris on the fluid tip or a loose air cap. Turn off the air, clean the fluid tip, and tighten the air cap.
  • T
    Timothy BradleyAug 27, 2025
    How to fix side heavy spray pattern in Ingersoll-Rand 9115?
    • H
      Heather MendezAug 27, 2025
      A side heavy spray pattern can occur due to debris in the right or left side holes of the air cap, or debris on the fluid tip. To fix this, turn off the air supply, clean the air cap holes and fluid tip using a non-metallic object like a toothpick.

Summary

Placing the Paint Sprayer in Service

Using the Paint Sprayer

Warning Symbol Identification

Agency Symbol Identification

European Community Mark

Indicates compliance with relevant EC directives.

Operations

Spray Gun Handling

Instructions on how to hold and operate the spray gun correctly for optimal results.

Air Adjustment

Guidance on setting the correct air pressure and flow for the spray gun.

Pattern Control

How to adjust the fan pattern size using the pattern control knob.

Fluid Control

Adjusting the fluid control knob to regulate paint atomization and flow.

Installation

Specifications

Maintenance

Declaration of Conformity

Exploded Diagram

Parts List

List of all available replacement parts with their corresponding part numbers.

Troubleshooting

Service Centers

Ingersoll-Rand 9115 Specifications

General IconGeneral
BrandIngersoll-Rand
Model9115
CategoryPaint Sprayer
LanguageEnglish

Related product manuals