Need help?Do you have a question about the IngMar Medical Laerdal ASL 5000 Lung Solution and is the answer not in the manual?
Details the limited warranty for materials and workmanship for one year.
Outlines liability limits, disclaims other warranties, and lists trademarks.
Outlines terms and conditions for software and documentation use.
Specifies government use restrictions and export compliance for the software.
Emphasizes reading and observing instructions, warnings, and cautions for safe operation.
Describes the ASL 5000™ Lung Solution's role in enhancing Laerdal simulators.
Explains the permanent fixture lung adapter for SimMan® and mode switching.
Details SimBaby™ adapter and Nursing Anne™ integration with ASL 5000™.
Introduces six ASL 5000™ windows within the LLEAP environment.
Controls ASL 5000™ connection, volume/gas conditions, and simulation.
Provides predefined patient types and disease states for easy access.
Controls airway resistance and lung compliance, single or dual models.
Controls breath rate and muscle pressure for spontaneous breathing.
Displays waveforms for pressure, flow, volume, and relevant breath parameters.
Provides real-time analysis of breathing mechanics via EOM components.
Details the three major components: Lung Adapter hardware, software installer, and simulator.
Explains how to switch between SimMan® and ASL 5000™ modes.
Describes the physical selector plate used to switch modes.
Step-by-step instructions for switching from SIM to ASL mode.
Step-by-step instructions for switching from ASL to SIM mode.
Guides on preparing the SimMan® manikin for the ASL 5000™ connection.
Steps to prepare the simulation environment for SimMan®.
Instructions for configuring the network connection for SimMan®.
Steps for connecting SimMan® in AP mode.
Details configuring ASL 5000™ connection settings in ASL Session Control.
Instructions on completing the ASL 5000™ connection.
Steps for connecting SimMan® in Client mode.
Details configuring ASL 5000™ connection settings for client mode.
Instructions on completing the ASL 5000™ connection in Client mode.
Connect SimMan® in Client mode requiring a unique IP address.
Details configuring ASL 5000™ connection settings for unique IP address.
Instructions on completing the ASL 5000™ connection by IP address.
Connect SimMan® as Virtual Simulator with physical ASL 5000™.
Steps to select the manikin in the LLEAP Select Virtual Simulator window.
Details configuring ASL 5000™ connection settings for Virtual Simulator.
Steps to revert SimMan® to its standard configuration.
Guides on preparing the SimBaby™ manikin for ASL 5000™ connection.
Steps for connecting SimBaby™ with the ASL 5000™ simulator.
Instructions for SimBaby™ operation when ASL 5000™ is not used.
Guides on preparing the Nursing Anne™ manikin for ASL 5000™ connection.
Instructions for network configuration for these manikins.
Steps to connect SimBaby™/SimMan® ALS/Nursing Anne™ using serial number.
Details configuring ASL 5000™ connection settings for these manikins.
Instructions for selecting ASL 5000™ by serial number.
Instructions on completing the ASL 5000™ connection by serial number.
Connect manikins requiring a unique IP address to ASL 5000™.
Details configuring ASL 5000™ connection settings for unique IP address.
Instructions for selecting ASL 5000™ by IP address.
Instructions on completing the ASL 5000™ connection by IP address.
Connect manikins as Virtual Simulator with physical ASL 5000™.
Steps to select the manikin in the LLEAP Select Virtual Simulator window.
Details configuring ASL 5000™ connection settings for Virtual Simulator.
Overview of ASL 5000™ windows within the LLEAP interface.
Displays LLEAP default and respiratory-centered theme examples.
Controls ASL 5000™ and simulation session with Play/Pause/Stop buttons.
Explains the Connect/Disconnect and Play/Pause/Stop buttons.
Opens ASL Configurator to set connection type and volume conversions.
Shows Tidal Volume (OFF) and Total Volume (ON) waveform displays.
Details volume conversion based on gas correction factors.
Explains Ethernet setup options: Device ID, Network Address, Static IP.
Guides on updating the ASL 5000™ simulator firmware.
Provides preconfigured patient types and lung disease states.
Allows adjustment of disease severity and setting patient to passive via Apnea.
Table detailing lung settings for various patient models in Quick Choice library.
Instructions on saving a custom lung model with a specified name.
Managing custom disease states via import, export, and deletion.
Steps to export a created custom lung model.
Steps to import a custom lung model.
Analyzes waveforms and readings directly from the lung simulator.
Explains pressure, flow, and volume waveforms and breath parameters.
Provides real-time analysis of breathing mechanics via EOM components.
Controls patient's lung and airway mechanics (resistance, compliance).
Setting up a single compartment lung model with resistance/compliance.
Setting up a two-compartment lung model with equal resistances.
Setting up single compartment model with unequal inspiratory/expiratory resistance.
Setting up two-compartment model with unequal inspiratory/expiratory resistance.
Controls spontaneous breathing and breath rate.
Details parameters for advanced control of breath effort.
Resolves issues when the Lung Solution software installer fails.
Troubleshoots issues with ASL 5000™ simulator connection status.
Addresses the issue of the ASL 5000™ red LED remaining illuminated.
General| Category | Medical Equipment |
|---|---|
| Model | ASL 5000 Lung Solution |
| Type | Lung Simulator |
| Compatibility | Compatible with various ventilators and respiratory devices |
| Connectivity | USB, Ethernet |
| Power Requirements | 100-240V AC, 50/60 Hz |
| Manufacturer | IngMar Medical |
| Control | Computer-controlled |
| Features | spontaneous breathing simulation |
| Application | Training, research |
To Next Page