Inovonics EN1221S-60 User Manual

11.10.20 357-06536-01 Rev A © Inovonics, 2020 - www.inovonics.com
EN1221S-60 Waterproof Pendant
Installation and Operation Manual
1 Overview
The Inovonics waterproof pendant is small, light and comfortable to wear,
and provides advanced functionality and reliability to enhance the user
experience.
The waterproof pendant is available in the following configurations:
Note: For UL 2560 installations, refer to the EN6080 Area Control Gateway
Installation Instructions or the EN6040-T Network Coordinator with
Transformer Installation Instructions.
1.1 Inovonics Contact Information
If you have any problems with this procedure, contact Inovonics technical
services:
• E-mail: support@inovonics.com.
• Phone: 1.800.782.2709, option 2.
1.2 Maximum Number of Repeaters for a UL 2560
Installation
To achieve the 99.99% alarm message reliability required for UL 2560
compliance, system installations must operate within the following limits for
end device and repeater counts.
1.3 Pendant Components
Figure 1 Pendant components (waterproof pendant with neck lanyard
shown)
2 Installation and Startup
2.1 Installation Notes
• These products are designed to be maintained by professional
technicians.
• Products are intended for indoor use.
• Do not ship the pendant with the coin cell battery installed when
temperatures are below 32°F. Doing so will damage the internal
battery and cause the pendant to irretrievably fail.
• All products should be manually tested weekly (see section 6, “Test
the Transmitter”).
2.2 Coin Cell Battery Installation
Caution: If you are installing batteries in multiple devices, keep the
batteries from coming into contact with each other to prevent discharge.
1. Place the battery in the battery compartment, ensuring that the positive
terminal (+) faces up.
2. Seat the battery door over the battery so that the arrow on the battery
door is lined up with the unlocked padlock icon.
Figure 2 Battery door in the unlocked position
3. Use the ACC680 alarm clearance card or a quarter to turn the battery
door to line up the arrow on the battery door with the arrow under the
locked padlock icon.
Figure 3 Battery door in the locked position
4. Press the activation button for at least one second.
Part # Check-In Location Other
EN1221S-60N 60 minutes North America Neck lanyard
EN1221S-60AN 60 minutes Australia Neck lanyard
EN1221S-60ZN 60 minutes New Zealand Neck lanyard
EN1221S-60W 60 minutes North America Wristband
EN1221S-60WL 60 minutes North America Long wristband
EN1221S-60AW 60 minutes Australia Wristband
EN1221S-60ZW 60 minutes New Zealand Wristband
For product and installation videos visit us at
www.inovonics.com/videos or use the QR
code below.
End Devices Maximum
Repeaters
150 397
250 386
350 375
500 360
1000 313
2000 238
3000 184
A Activation button B Transmit and alarm clear
LED
C Low battery LED
D Battery door E Attachment loop
B
C
A
D
E
Unlocked
position
Locked
position

Inovonics EN1221S-60 Specifications

General

Brand	Inovonics
Model	EN1221S-60
Category	Telephone Accessories
Language	English

Summary

Inovonics Pendant Installation

Pendant Components Overview

Identifies key components of the waterproof pendant, including activation button, LED, and battery door.

Installation and Startup Notes

Provides essential notes for professional technicians, including indoor use and handling precautions for cold temperatures.

Coin Cell Battery Installation

Step-by-step guide on how to install the CR2032 coin cell battery correctly into the pendant.

Registering the Transmitter

Explains the process of registering the transmitter with the receiver or gateway for supervision.

Wearing the Transmitter

Details the methods for wearing the pendant using a neck lanyard or wristband, including attachment.

Operating the Inovonics Pendant

Sending and Clearing Alarms

Instructions on how to send an alarm using the activation button and how to clear it using the button or card.

Coin Cell Low Battery Alert

Describes the low battery alert system, including LED indicators and countdown timers.

Coin Cell Battery Replacement

Provides detailed steps for replacing the CR2032 coin cell battery in the pendant.

Storage Mode Operations

Covers putting the device into and taking it out of storage mode for battery preservation.

Testing the Transmitter

Guidance on how to test the transmitter's functionality after registration and on a weekly basis.

Cleaning and Care

Recommendations for cleaning the pendant using mild soap and avoiding harsh chemicals or sterilization.

Device Information and Compliance

Device Indicators and Alerts

Explains the meaning of different LED colors and vibration patterns for alarm, low battery, and missing battery.

Water Exposure Guidelines

Details the pendant's water resistance (IP67) and recommendations for use in wet environments.

End User Recommendations

Provides advice for end users on shower use, water exercise, and avoiding high pressure water spray.

Technical Specifications

Lists key specifications including dimensions, weight, operating temperature, and battery life.

Power Management and Shipping

Information on the two-stage power system, battery handling, and shipping recommendations for cold weather.

Regulatory Compliance and Interference

Covers FCC, Industry Canada compliance, RF exposure, and potential interference with medical devices.