FEATURES
INSTALLING A BATTERY
1 Remove the battery cover, then insert a AA battery. Make sure that the +
and – match the symbols inside the battery compartment.
2 Replace the battery cover.
TROUBLESHOOTING
CONNECTING YOUR MOUSE
Windows OS:
1 Slide the power switch to ON, then press the connect button on the
bottom of your mouse. The LED indicator blinks.
2 Click the Bluetooth icon in your computer’s taskbar.
Note: If your adapter is turned o, right-click the icon, then select Turn adapter
on.
3 Click Add a device. Your computer searches for your mouse.
4 Double-click Insignia Bluetooth Mouse. When pairing is complete, the
LED indicator turns o.
Mac OS:
1 Slide the power switch to ON, then press the connect button on the
bottom of your mouse. The LED indicator blinks.
2 Open System Preferences, then click Bluetooth.
3 Click + in the lower-left corner. Your computer searches for your
mouse.
4 Double-click Insignia Bluetooth Mouse. When pairing is complete, the
LED indicator turns o.
Note: If your computer has never connected to a Bluetooth device, click Set Up
New Device to pair your mouse to your computer.
UN-PAIRING YOUR MOUSE
Windows:
1 Click the Bluetooth icon on your task bar.
2 Click Show Bluetooth Devices.
3 Right-click Insignia Bluetooth Mouse.
4 Click Remove Device to un-pair the mouse.
Mac:
1 Open System Preferences, then click Bluetooth.
2 Click the – in the lower-left corner.
3 When it asks Are you sure you want to remove this device?, click Remove.
LEGAL NOTICES
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
FCC Caution
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate
this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
maybe cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent form that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
RSS-Gen & RSS-247 statement:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
RSS-102 Statement:
This equipment complies with Industry Canada radiation exposure limits set forth for an uncontrolled environment.
Cet équipement est conforme à l'exposition aux rayonnements Industry Canada limites établies pour un environnement non contrôlé.
ONE-YEAR LIMITED WARRANTY
For complete warranty, visit www.insigniaproducts.com.
CONTACT INSIGNIA
1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2016 Best Buy. All rights reserved.
Made in China
Before using your new product, please read these instructions to prevent any damage.
PACKAGE CONTENTS
• Wireless mouse
• AA battery
• Quick Setup Guide
SYSTEM REQUIREMENTS
• Windows® 10, Windows® 8.1, Windows® 8, Windows® 7, or
Mac OS X 10.4 or higher
• Built-in Bluetooth function or Bluetooth receiver
USING YOUR MOUSE
Turning your mouse on or o
• Slide the OFF/ON switch to turn your mouse o or on.
• Your mouse sleeps after 10 minutes of inactivity to save battery life.
Move your mouse or press a button to wake it up.
Adjusting mouse sensitivity (DPI):
Note: The default setting is 1200 DPI.
• Press the DPI button to toggle between 800, 1200, or 1600 DPI. The
LED blinks when you switch the sensitivity:
• You may also be able to adjust your mouse sensitivity with your
computer’s settings. See your operating system’s instructions for more
information.
CLEANING YOUR MOUSE
• Wipe the mouse with a damp, lint-free cloth.
SPECIFICATIONS
• Dimensions (L × W × H): 2.78 x 1.56 x 3.73 in. (7.05 x 3.94 x 9.48 cm)
• Weight: 3.07 ± 0.18 oz. (87 ± 5 g)
• Battery: 1 AA alkaline battery
• Battery life: 6 months (based on average usage)
• Operating distance: 33 ft (10 m)
• Radio frequency: Bluetooth 3.0
• Compatibility: Bluetooth 2.1, 3.0, 4.0, 4.1
• Rating: 1.5V C.C – 10mA
Final at size: 942.93 x 148.08 mm
Final fold size: 104.77 x 148.08 mm
FUNCTION
LED indicator
Connect button
DESCRIPTION
• Lights for ten seconds when you turn on your mouse.
• When the connect button is pressed, the red LED keeps
blinking until paired successfully or pairing time-out (ten
minutes).
• Low battery warning: Blinks for six seconds when mouse
stops moving.
Press to put your mouse in pairing mode.
QUICK SETUP GUIDE
Bluetooth
Mouse
NS-PNM3B8BK
PROBLEM:
My mouse is not
working.
The screen cursor
does not move
properly.
SOLUTION:
• Make sure that the battery is installed correctly and that the switch is
turned ON. Replace the battery if it still does not work.
• Move your mouse closer to your computer.
• Make sure that your computer meets the system requirements.
• Make sure that your mouse is paired by pressing the connect button
on the bottom of your mouse, then pair it with your computer.
• Make sure that the Bluetooth function on your computer or Bluetooth
receiver is working.
• Un-pair your mouse from your computer, then re-pair it.
If your screen cursor lags behind the movement, then your Bluetooth
connection may not be able to transmit all of the data from the mouse
with the necessary speed. This may be caused by interference from other
radio sources, obstructions in the radio wave path, excessive distance
from the computer, or a combination of the above.
• Remove any metallic objects from the line of sight between your
computer and the Bluetooth mouse.
• If you are using a computer with a built-in Bluetooth antenna, try
reorienting the computer until you get a better data rate.
• If you are using a Bluetooth dongle, use a USB extension cable and
place the Bluetooth dongle onto your desktop or somewhere in sight
of your Bluetooth mouse.
• Move the mouse closer to your Bluetooth dongle.
• Turn o the mouse, and then turn it on again for a better connection.
• Disconnect any Bluetooth audio devices, such as headsets, that may
be connected to your computer.
• Switch o any other devices operating in the 2.4 GHz radio spectrum,
such as a Wi-Fi network or mobile telephone, or move their antennas
further away from your computer.
BackwardForward
Left button
Right button
Scrolling wheel
DPI button/
LED indicator
Battery cover
OFF/ON switch
Connect button
AA battery
LED blinks once
800 DPI
LED blinks 2 times
1200 DPI
LED blinks 3 times
1600 DPI
CARACTÉRISTIQUES
INSTALLATION DE LA PILE
1 Retirer le couvercle du compartiment de la pile et insérer une pile AA.
Veiller à ce que les symboles + et – coïncident avec les symboles + et –
gurant à l'intérieur du compartiment.
2 Remettre le couvercle du compartiment de la pile.
CONNEXION DE LA SOURIS
Système d’exploitation Windows :
1 Faire glisser le bouton de marche-arrêt sur ON (Marche), puis appuyer
sur le bouton de connexion (connect) en dessous de la souris. Le
témoin à DEL clignote.
2 Cliquer sur l’icône Bluetooth dans la barre des tâches de l'ordinateur.
Remarque : Si l'adaptateur est hors tension, cliquer avec le bouton droit de la
souris sur l'icône et sélectionner Turn adaptateur on (Mettre l'adaptateur sous
tension).
3 Cliquer sur Add a device (Ajouter un périphérique). L'ordinateur
cherche à détecter la souris.
4 Double-cliquer sur Insignia Bluetooth Mouse (Souris Bluetooth
Insignia). Quand le couplage est terminé, le témoin à DEL s'éteint.
Système d'exploitation Mac :
1 Faire glisser le bouton de marche-arrêt sur ON (Marche), puis appuyer
sur le bouton de connexion (connect) dans la partie inférieure de la
souris. Le témoin à DEL clignote.
2 Ouvrir System Preferences (Préférences système), puis cliquer sur
Bluetooth.
3 Cliquer sur + dans le coin inférieur gauche. L'ordinateur cherche à
détecter la souris.
4 Double-cliquer sur Insignia Bluetooth Mouse (Souris Bluetooth
Insignia). Quand le couplage est terminé, le témoin à DEL s'éteint.
Remarque : Si l'ordinateur n'a jamais été connecté à un périphérique Bluetooth,
cliquer sur Set Up New Device (Conguration d’un nouveau périphérique) pour
coupler la souris avec l'ordinateur.
DÉCOUPLAGE DE LA SOURIS
Windows :
1 Cliquer sur l’icône Bluetooth dans la barre des tâches.
2 Cliquer sur Show Bluetooth Devices (Acher les périphériques
Bluetooth).
3 Cliquer avec le bouton droit sur Insignia Bluetooth Mouse (Souris
Bluetooth Insignia).
4 Cliquer sur Remove Device (Supprimer Périphérique) pour découpler la
souris.
Avant l’utilisation de ce produit neuf, lire ces instructions an d'éviter tout dommage.
CONTENU DE L'EMBALLAGE
• Souris sans l
• Pile AA
• Guide d’installation rapide
CONFIGURATION SYSTÈME REQUISE
• Windows
MD
10, Windows
MD
8.1, Windows
MD
8, Windows
MD
7 ou
Mac OS 10.4 ou plus récent.
• Fonction Bluetooth intégrée ou récepteur Bluetooth
FONCTION
Témoin DEL
Bouton de
connexion
DESCRIPTION
• S'allume pendant dix secondes quand la souris est mise sous
tension.
• Quand le bouton de connexion (Connect) est appuyé, la DEL
rouge clignote jusqu'à ce que le couplage soit eectué ou
qu'il ait échoué (dix minutes).
• Alerte de pile faible : clignote pendant six secondes quand
la souris ne bouge plus.
Appuyer sur cette touche pour mettre la souris en mode de
couplage.
GUIDE D’INSTALLATION RAPIDE
Souris Bluetooth
NS-PNM3B8BK
Retour arrière
Avance rapide
Bouton gauche
Bouton droit
Molette de délement
Bouton ppp/
témoin à DEL
Couvercle du
compartiment
de la pile
Commutateur
MARCHE-ARRÊT
Bouton de
connexion
Pile AA
NS-PNM3B8BK_16-1067_QSG_V2_TRI.ai 1 12/7/2016 2:53:07 PMNS-PNM3B8BK_16-1067_QSG_V2_TRI.ai 1 12/7/2016 2:53:07 PM
To Next Page
Need help?
General
