This document describes the InSinkErator Steaming Hot Water Tap, a device designed to provide instant hot water for various kitchen tasks. The manual covers installation, usage, maintenance, and safety guidelines for the tank replacement process.

The primary function of the InSinkErator Steaming Hot Water Tap is to deliver near-boiling water on demand, making it convenient for preparing hot beverages, cooking, and other kitchen needs. The system consists of a tap and an under-sink tank that heats and stores water.

Installation and Setup:

Before installation, it is crucial to read all instructions, cautions, and warnings to ensure safety and proper operation. All electrical wiring and connections must conform to local codes. A standard, grounded electrical outlet is required under the sink, and it must provide continuous power. The outlet should be fused (10 amp for 230V/220-240V UK, 15 amp for 120V) and not controlled by the same wall switch as a food waste disposer.

The water pressure must be maintained between 172 kPa and 862 kPa (25-125 psi), with an ambient temperature between 10°C and 38°C. In Australia, an Australian WaterMark approved 350 kPa set pressure limiting valve and dual check valve are required.

The installation process involves several steps:

Preparation: Turn off the water supply and unplug the old tank. Run water from the old tank until cool. Remove the inlet, outlet, and vent tubes from the fittings. Lift the old tank off its mounting bracket or screws and drain any remaining water into a sink or container. A towel should be available for cleanup as a minimal amount of water might spill.
Mounting the Tank: The new tank must be mounted level to ensure proper operation. It should be positioned vertically within 400mm of the faucet water lines and within 760mm of a standard grounded outlet. Mark locations for two hanging screws, leaving 6.4mm for the hanging tank. Pre-drill 3mm pilot holes and install the provided screws (for wood only) or use wall anchors (for drywall), leaving 6.4mm exposed. Hang the new tank on the screws and tighten them 1/2 turn clockwise, being careful not to overtighten.
Connecting Lines: Attach the inlet tube to the tank. Then, attach the outlet and vent tubes to their respective fittings. Note that snap connect fittings are not included and may be required for tanks manufactured prior to January 2006.
Filling the Tank and Connecting Power: Turn on the water supply. Activate the HOT handle and hold it until water flows from the spout (approximately 1-2 minutes). To flush the lines, run water for at least 2 minutes (using both hot and cold handles if applicable). Check for leaks around all fittings. If no leaks are present, plug in the tank. It is crucial not to plug in the unit until water has flowed from the faucet.

Usage Features:

The InSinkErator Steaming Hot Water Tap is designed for ease of use. Once installed and powered, the tank will begin heating the water. Gurgling or hissing sounds are normal during the initial heating cycle. It typically takes 12-15 minutes for the water to reach the desired temperature. The tap provides instant access to hot water, making tasks like making tea, coffee, or preparing instant meals much quicker.

Maintenance Features and Safety Guidelines:

Regular maintenance and adherence to safety guidelines are essential for the longevity and safe operation of the steaming hot water tap.

Grounding: The appliance must be properly grounded to prevent electric shock. The power cord is equipped with a grounding conductor and a grounding pin. The plug must be connected to an appropriate, properly installed, and grounded outlet in accordance with all local codes. Do not alter or remove the ground pin from the power cord, and do not use an extension cord set with the unit.
Water Quality: To ensure proper operation, the unit is not intended to be flushed with chlorine. If elevated levels of chlorine are suspected in the water, using a water filtration system is recommended.
Tank Integrity: The tank is a non-pressurized unit. Do not modify the system, close the vent tube, or connect other types of taps or valves to the tank. Only use parts provided by InSinkErator. Contact an authorized InSinkErator Service agent for repairs or replacement components.
Leak Prevention: Regularly inspect the dispenser and plumbing fittings for leaks. Leaks can cause property damage and personal injury. A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in applications where leakage could cause property damage.
Corrosion Check: Examine the appearance of dispensed water in a clear glass every three months. If there is any discoloration or rusty appearance, unplug and drain the unit. If the water discoloration persists after draining and refilling, discontinue use and contact an authorized InSinkErator service agent.
Fire Hazard: Do not store flammable items (rags, paper, aerosol cans, gasoline, or other flammable vapors and liquids) near the tank or any other appliance.
Product Lifespan: Like any water heater, the steaming hot water tap has a limited life and will eventually fail. To avoid property damage and personal injury, the tap should be regularly examined for leakage and/or corrosion and replaced when necessary.

Warranty Information:

The product comes with a warranty provided by InSinkErator. The warranty covers defects in materials and workmanship for a specified "Warranty Period," which begins on the later of the original installation date, purchase date, or manufacturing date (identified by the serial number). Documentation supporting the installation or purchase date is required. The warranty covers replacement parts and labor costs for residential use only.

The warranty does not cover losses or damages resulting from conditions beyond the manufacturer's control, including accident, alteration, misuse, abuse, neglect, improper installation, or failure to maintain the product according to instructions. Normal wear and tear, such as cosmetic rust, scratches, and dents, are also not covered. The warranty does not apply to products installed in commercial or industrial applications.

In the event of a covered claim, InSinkErator or its authorized service representative will either repair or replace the product at no cost to the customer. Repair or replacement will be determined at their sole discretion. All services will be provided at the customer's home. The warranty on a replacement product will be limited to the unexpired term of the original warranty.

InSinkErator's liability is limited to the price paid by the original owner for the product and does not cover incidental, special, indirect, or consequential damages, including economic loss, business interruption, or loss of use or revenue.

InSinkErator HWT-00 - Page 3

Related product manuals