10
STORING, WINTERIZING, & TRANSPORTING
Save the original shipping carton from the spa for storing and transporting. Before
re-packing, make sure all components are completely dry and clean.
Winterizing/Vacationing- If you are taking a vacation or leaving your InstaSPA
outdoors and unused for a week or more, you should leave the cover on, air control
valve closed, and set the temperature control to 26.67 degree C (80 degree F). This
will protect the InstaSPA from freezing, yet continue to filter the spa water to maintain
cleanliness. Upon return, adjust the water chemistry to correct chlorine and pH
levels. Increase temperature to desired level. If you are leaving your spa for an
extended period of time, or do not plan on using it, drain your system completely.
Turn the motor unit so that the hoses are facing down, and allow all water to drain
from the internal plumbing. Failure to do so may cause the water to freeze and
severely damage your motor unit.
FILLING SPA
Fill with a hose and tap water. ALWAYS UNPLUG THE SPA from its electrical source
before filling (or draining). To reduce the time needed for the initial warm up, you
can use hot water to fill the spa. You can purchase a hose adapter for your hot water
tap from a harware store. Do not use water with a temperature over 40 degree C
(104 degree F). Fill the spa slowly (over a period of a few hours). This allows your
home’s water heater to recover and supply enough hot water.
DRAINING SPA
Indoor installations can be drained using a submersible sump pump.
ALWAYS UNPLUG THE SPA from its electrical source before draining (or filling).
Remove the Vinyl Outer Skirt from the Spa, and connect a hose pipe to the Drain
Valve located near the bottom of the Inner Liner, close to the Spa Hoses.
Reach inside the Spa, under water, and open the Drain Plug on the inside of the Spa.
The water will drain from the spa out of the hose. To stop draining, simply close the
Drain Plug.
Drain Valve
Inside Spa
Drain Valve Outside Spa
Attach hose to run water away
Drain Valve Inside Spa
Shown Open
Care and Maintenance
CLEANING SPA
Empty the InstaSPA and refill with clean water 2-3 times per year
or when it becomes cloudy and proper water chemistry does not
clear it up.
When empty, use a mild soap solution to wipe any soil or stains
on the inner liner. Rinse thoroughly before refilling the spa. Do
not use cleaning aids such as steel wool, steel bristle brushes or
abrasive cleaners. Improper use of these products can void the
warranty.
THE EXTERIOR OF THE SPA AND COVER ARE MADE OF HIGH
GRADE PVC WHICH IS SPECIALLY FORMULATED TO RESIST
CRACKING AND DISCOLORATION. IF THE INSTASPA IS LOCATED
OUTSIDE, OVER TIME, IT IS NATURAL FOR THE COLOR OF THE
PVC MATERIAL TO FADE SLIGHTLY DUE TO EFFECTS FROM THE
SUN AND RAIN. THIS WILL NOT AFFECT THE PERFORMANCE AND
DURABILITY OF THE SPA.
CARE and MAINTENANCE
Water Level- Always keep the water level at least 2 inches ABOVE the suction
valve. Lower water levels can cause the motor unit overheat and void the
warranty.
CHANGING AND CLEANING THE FILTER
The water filtration unit is located between the
motor and the Spa body. It has a transparent top
so that you can easily see when it needs cleaning.
When dirty, or once a week, remove the filter
and wash it under a tap of warm water. Replace
the filter entirely after 3 months of continuous
use with CSA recommended filters.
HOW TO CHANGE FILTER
SWITCH THE SPA JETS ON. Then unscrew
the filter cap. It is important to have the jets
operating when you open the filter cap. The jets
create a vacuum and keep the water from
overflowing. If the jets are off, then water will
overflow when the filter cap is removed.
InstaSPA
™
InstaSPA
™
InstaSPA
™
To Next Page
Loading...