Instek Digital LCR-819 - User Manual

LCR-800 Series User Manual
i
CONTENTS PAGE
1. INTRODUCTION……………………………………..……... 1
2. PRECAUTIONS BEFORE OPERATION…….…………….
2-1.Unpacking the instrument………………….…………….
2-2.Checking the Line Voltage…………………..……………
2-3.Environment……………………………………..………..
2-4.Equipment Installation and Operation…………………
2
2
2
3
3
3. PANEL DESCRIPTION…...……………………..………….. 4
OPERATION…………….………………………………...….
4-1.Connects to DUT….………………..………….……..…...
4-2.Start-Up……….....……………………………..………….
4-3.Zeroing…………………………………………………….
4-4.Menu Functions.…..………………………………………
4-5.Measurement Conditions…..……………………………..
8
8
8
8
11
18
4.
5.
SPECIFICATIONS…………………………………………...
35
6. MESSAGE CODE.………………………………………….... 44
7. MAINTENANCE....…………………………………………...
7-1.Cleaning……………………………………………………
7-2.Battery Replacement……………………………………...
7-3.Recall Calibration………………………………………...
45
45
45
46
8. OPTION 1 (BIN Function for LCR-826/827/829 only)……..
8-1. BIN Functions for Components Sorting……………..….
8-2. BIN Setting Conditions.....……………………………….
8-3. BIN Range Setting: Component Sorting Range..............
48
48
50
56
9. OPTION 2……………………………………………………..
9-1.On-line procedure…………………………………………
9-2.RS232 VIEWER Software Operation…………………...
9-3.The Configuration of Cable………………………………
65
65
69
74
LCR-800 Series User Manual
ii
SAFETY TERMS AND SYMBOLS
These terms may appear in this manual or on the product:
WARNING: Warning statements identify condition or practices
that could result in injury or loss of life.
CAUTION: Caution statements identify conditions or practices
that could result in damage to this product or other property.
The following symbols may appear in this manual or on the product:
DANGER ATTENTION Protective Frame or Chassis
High Voltage refer to Manual Conductor Terminal
Terminal

Summary

Safety Terms and Symbols

Precautions Before Operation

Operation

Basic Operation and Zeroing Procedures

Steps for connecting the DUT, starting up the instrument, and performing open/short circuit zeroing for accuracy.

Menu Functions and Measurement Settings

Overview of menu-driven functions, including parameter selection, measurement modes, and condition settings like frequency, voltage, and speed.

Specifications

Measurement Parameters and Display Ranges

Maintenance

Cleaning and Battery Replacement

Option 1: BIN Functions

BIN Functions for Component Sorting

Setup and usage of the BIN function for sorting components based on measurement criteria.

BIN Setting Conditions and Ranges

Option 2: RS-232 C Communication

On-line Procedure

Steps to establish an on-line connection between the LCR meter and a computer using RS-232C.

RS232 VIEWER Software Operation

Instek Digital LCR-819 Specifications

General

Type	Digital LCR Meter
Test Frequency	100Hz, 120Hz, 1kHz, 10kHz, 100kHz
Basic Accuracy	0.1%
Output Impedance	100Ω
Equivalent Circuit Mode	Series, Parallel
Frequency Range	100Hz to 100kHz
Accuracy	±0.1%
Test Signal Level	0.3Vrms, 1.0Vrms
Display	LCD with backlight
Measurement Parameters	L, C, R, D, Q, θ
Interfaces	USB, RS-232
Output Interface	USB
Measurement Speed	3 times per second
Power Supply	AC 100V to 240V, 50/60Hz