Interlogix Simon XT Quick Reference

TestingyourSystemcommunication
,NOTE:callthemonitoringstationfirsttoplaceyouraccountontest(APIMonitoring1‐800‐268‐
6870).Oncecompletedconfirmwiththemonitoringstationthattheyreceivedthetestsignaland
takeyoursystemofftest.

1. Scrollup/downtoSystemTestsandpress
[ENTER]
2. ThedisplayshowsEnterCode.Enteryour[MASTERCODE]andpress[ENTER]
3. Scrollup/downtoCommTest.Press[ENTER]
4. ThedisplayshowsCommTestisOn
5. Afterthecommunicationtestissuccessful,thedisplayshowsCommTestOk
6. Press[STATUS]repeatedlytoexit.

a
NOTE:Ifthecommunicationtestisunsuccessful,theSTATUSbuttonwilllightandwithinten
minutesthepanelwilldisplayCommFailure.PleasecontactReedSecurity(306)653‐3200,during
normalbusinesshours,fortroubleshootingassistanceortoarrangeforaservicecall.


Troublebeeps‐CallReedSecurityforservice(306)653‐3200
,NOTE:sixrapidbeepseveryminuteindicateatroublesituation.Tostopthebeeps,press[STATUS]
orarm/disarmthesystem.Thebeepswillresumefourhourslaterunlessthetroubleconditionis
corrected.Pressingthe[STATUS]buttonwillshow
thecauseofthetroubleonthedisplay.Ie:Power
failure,lowbatteries,nonworkingsensors,communicationtroubleswiththemonitoringstation.

Replacingthebackupbattery
1. Callthemonitoringstationat1‐800‐268‐6870toplaceyoursystemontestforabout30min.
Haveyouraccountnumber
(e.g.58‐1234)aswellasyourpasswordready.
2. Makesureyoursystemisdisarmed(“DISARMED”onthedisplay)
3. Openthekeypadbypressingdownonthe2smalltabsonthetopofthepanelandpulling
thetoptowardsyou,lettingthekeypadhangfromthehinges.

4. Removethebatteryanddisconnectthewireleads.
5. FindtheA/Cpowersupplyandunplugit.(Itiswhite,asbigasafistandusuallyeitherbeside
thekeypadorintheutilityroom)
6. Atyourkeypad,connecttheblackleadwiththeblackterminalofthenewbatteryandthe
redleadwiththeredterminalandputthebatteryinthecompartment.Thepanelwillnow
bepoweredupbeeping,ignorethisfornow.
7. PlugtheA/Cpowersupplybackinandclosethekeypadpanel.
8. Thekeypadwillnowbelitup
blueandbeeping.Press[STATUS]andthevoicemessage
shouldonlysay“timenotset”.Tosetthetime:
a. Pressthedownarrowuntilthescreenshows“settime12:00am.”.Press[ENTER]
b. Enteryour[mastercode],press[ENTER]
c. Usingthenumberkeys,enterthecurrenthour
(e.g.[08]for8a.m.),press[ENTER]
d. Entertheminutes(e.g.[30]for8:30a.m.),press[ENTER]
e. Press[STATUS]twiceandthevoiceshouldsay“systemisok”

FORACOMPLETEMANUAL,FORYOURSYSTEM,VISITOURWEBSITEAT:
www.reedsecurity.com
goto“quickhelp”,then“downloads”andscrolltofindyoursystemmanual


Interlogix Simon XT Specifications

Power

power requirements	6V nominal
standby current	30mA (10mA in PowerSave Mode)
peak current	1.7 A

Operating Environment

operating temperature	32 to 120°F (0 to 49°C)
storage temperature	-30 to 140°F (-34 to 60°C)
max. relative humidity	90% non-condensing

Dimensions

height	4 1/16 in.
width	1 7/8 in.