The RF-7220-07-1 Wireless Outdoor Siren is a robust security device designed to provide audible and visual alerts in an outdoor environment, integrating seamlessly with compatible security systems. This installation sheet provides comprehensive instructions for its setup, configuration, and maintenance.
Function Description
The primary function of the RF-7220-07-1 is to act as a wireless outdoor siren, emitting loud alarms and flashing a beacon to deter intruders and alert nearby individuals during a security event. It is designed to be learned into a security panel, allowing the system to control its activation. The siren incorporates a tamper switch for enhanced security, triggering an alarm if the unit is removed from its mounting surface. An IO module within the siren allows for configurable output control.
Important Technical Specifications
- Power Supply: The siren operates on a BS7201-N, 4-cell custom lithium battery pack (purchased separately).
- Battery Capacity: 12.5 Ah.
- Operating Voltage:
- Electronics, board: 3.0 VDC
- Siren/flash light part: 12.0 VDC
- Battery Lifetime (typical): 3 years, based on an assumption of maximum 20 siren activations of 3 minutes and beacon activations of 15 minutes per year.
- Current Consumption (typical):
- IO module: 140 µA at 3.0 VDC ± 10%
- Siren: 340 mA at 12.0 VDC ± 10%
- Beacon: 74 mA at 12.0 VDC ± 10%
- Environmental Conditions:
- Operating Temperature: -25°C to +50°C
- Humidity: max 95%, non-condensing
- Physical Dimensions:
- Shipping Weight: 2.3 kg
- Enclosure Dimensions: 310 x 222 x 91 mm
- Compliance:
- EN 50131 Grade and Class: Security Grade 2, Environmental Class III
- Certifications: EN 50131-5-3:2005, EN 50131-5-3/A1:2008, EN 50131-4:2009. Tested and certified by Telefication B.V.
- EU Compliance: CE
- Directives: 2012/19/EU (WEEE), 2006/66/EC (battery), 1999/5/EC, 2014/30/EU, 2014/35/EU.
Usage Features
- Wireless Integration: The siren is designed for wireless communication with a compatible security panel, simplifying installation and reducing wiring requirements.
- Learning-in Process: The siren must be "learned-in" to the security system. This involves entering programming mode on the panel, navigating to zone settings, selecting a zone for the siren, and then powering up the siren with the tamper switch open. The system will detect and register the siren, displaying its serial number.
- Multiple Zone Occupation: The outdoor siren can occupy up to 4 zone numbers within the security system.
- Configurable Cut-off Timer: Jumpers J1 and J2 on the siren's PCB allow for configuration of the siren's cut-off timer, with options for 3, 5, 10, or 20 minutes. Jumper 3 acts as a start-up protection and must be cut to enable the IO module to control the siren's output.
- Tamper Protection: A tamper switch is integrated into the design, triggering an alarm if the siren is removed more than 5 mm from its mounting surface. Proper installation requires careful positioning of the tamper switch lever against the wall and securing it with a screw to ensure adequate pressure.
- Visual Indication: The siren includes a beacon (flash light) for visual alerts, complementing the audible alarm.
Maintenance Features
- Battery Replacement: The siren requires a BS7201-N lithium battery pack. To replace the batteries, the black plastic strap holding the pack should be pulled. It is crucial to only use the specified lithium battery type and to purchase it separately.
- Safety Instructions for Battery Handling:
- Batteries can explode or cause burns if recharged, incorrectly (dis)assembled, or exposed to fire or high temperatures.
- Used batteries must be disposed of according to battery directive instructions and local laws, kept away from children.
- High Voltage Warning: Do not open the flash housing due to the risk of high voltage.
- Regulatory Compliance: The device adheres to various European directives regarding waste electrical and electronic equipment (WEEE) and batteries, emphasizing proper recycling and disposal methods. Information on recycling can be found at www.recyclethis.info.
- Customer Support: For customer support, users can refer to www.utcfssecurityproducts.eu. General contact information is available at www.utcfireandsecurity.com or www.interlogix.com.
Need help?
General
To Next Page