Intex Downy Full - BUILT-IN FOOT PUMP; Before Inflating with Built-in Foot Pump; Inflating Using the Built-in Foot Pump; Inflating Using an External Air Pump

(15IO) INSTRUCTION SHEET SIZE: 7.5” X 10.3” 04/18/2022
©2022 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Recreation Corp. All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte
vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/Marcas registradas utilizadas en algunos países
del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in Lizenz von/
Intex Marketing Ltd. to/à/a/an Intex Development Co. Ltd., Hong Kong & Intex
Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 •
Distributed in the European Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/
Vertrieb in der Europäischen Union durch/
Intex Trading B.V., Ettenseweg 46, 4706 PB Roosendaal – The Netherlands
• Distributed in the UK by
Unitex Service (UK) Limited,
21 Holborn Viaduct, London EC1A 2DY, UK.
www.intexcorp.com
15
IO
READ AND FOLLOW ALL INSTRUCTIONS
BEFORE INFLATING OR USE
BEFORE INFLATING WITH BUILT-IN FOOT PUMP
• Spread the air bed out on a at surface. Make sure this surface is free
of stones or others sharp objects which might puncture the air bed.
• The built-in air pump ination valve
1
must face up.
• Make sure that the insert plug is properly positioned and the 2 in 1
exhaust valve
2
cap is securely tightened.
TO INFLATE USING THE BUILT-IN FOOT PUMP
• Remove the air pump ination valve cap and insert plug
1
. Save the
cap and plug to reattach after ination.
• Locate and spread the built-in foot pump out to ensure the foot pump
surface is at and straight.
• Placing your foot directly over the ination valve opening, push rmly
down
3
. This will push air from the air pump chamber into the bed.
• Release your foot
4
so the air pump chamber will re-ll with air for
the next cycle.
• Repeat until desired rmness is achieved.
• Replace the air pump ination valve insert plug and cap
1
.
TO INFLATE USING AN EXTERNAL AIR PUMP
• Make sure the air pump ination valve
1
insert plug is properly
positioned and the 2 in 1
2
exhaust valve cap is securely tightened.
• Pull 2 in 1
2
valve cap to open.
• Insert the nozzle from an air pump into the 2 in 1
2
ination valve.
• Inate the product to approximately 80% of desired rmness.
CAUTION: To prevent bursting, do not over inate or use high
pressure air compressor.
• Close 2 in 1
2
valve cap securely after ination.
TO DEFLATE
• Pull out 2 in 1
2
valve cap.
• Pull ination valve base to release air.
CAUTION: When opening, point the exhaust valve away from
any person.
• Replace ination valve base and cap securely.
015-*IO-R0-2304
Air inside of bed may expand and contract with varying temperature
leading to reduce pressure inside of the bed. If this occurs, simply
add more air using the pump to achieve desired rmness. If
puncture occurs, please refer to instruction. Repair kit/patch is
enclosed.
IMPORTANT
3
4
1
2
2
DEFLATE
INFLATE
BUILT-IN FOOT PUMP
INTEX
®
OWNER’S MANUAL
English
–––– SAVE THESE INSTRUCTIONS ––––