Invacare 9670 - User Manual

For more information regarding Invacare products, parts, and services, please visit www.invacare.com
Transfer Bench 1 Part No 1148079
Transfer Bench
SAVE THESE INSTRUCTIONS
NOTE:CheckALLpartsfo rshippingdamage.Ifshippingdamageisnoted,DONOTuse.Contact carrier/dealerforfurtherinstruction.
 WARNING
• DO NOT install or use this equipment without first reading and understanding this instruction sheet. If you are unable to understand the warnings,
cautions or instructions, contact a healthcare professional, dealer or technical personnel, before attempting to install this equipment - otherwise,
injury or damage may occur.
• The transfer bench backrest and armrest MUST be installed before using the transfer bench.
• DO NOT submerge seat in water otherwise damage to seat may result.
• Check rubber tips for rips, tears, cracks or wear. If any of these conditions exist, replace rubber tips IMMEDIATELY.
• Users with limited physical capabilities should be supervised or assisted when using the transfer bench.
• Use seat arm only to assist in transfers. DO NOT attempt to use seat arm to assist in standing in tub, otherwise tipping of the transfer bench could
result.
• This product should only be used with tub floors wider than 18-5/8 inches.
• ALWAYS observe the weight limit on the labeling of this product. Check that all labels are present and legible. Replace if necessary.
• Most tub floors are higher than the bathroom floor. Before using, ensure that the four legs of the transfer bench inside the tub are adjusted to the
same height and the two legs outside the tub are adjusted to the same height, so as to achieve a level seat. If the transfer bench has suction feet, apply
all suction feet to the inside tub surface. DO NOT use the transfer bench if wobbly, unstable, or not level.
• After any adjustments, repair or service and before use, make sure all attaching hardware is securely tightened - otherwise injury or damage may
result.
• The seat arm is NOT intended to support the total body weight of the user.
• Model 9670 only - Make sure that the compression buttons on the back support tabs are completely visible through the notches on the back of the
seat before use.
CAUTION
• If the transfer bench has suction feet, pull the tabs up to release the feet from the tub. Otherwise, permanent damage may occur.
Set-Up
NOTE:Theseinstructionsarevalidforalltypesoftransferbenches,althoughmodelsvary .
Attaching the Back
Performoneofthefollowingdependingonbenchtype:
Model9670(DETAIL“A”) :
1. Pushthetabsonthebottomofthebackintotheholesintheseatuntilthe
compressionbuttonsarecomp letelyvisiblethroughthenotchesonthe
backoftheseat.
Othertransferbenchmodels(DETAIL“B”):
1. Positiontheback
supportonthebacksupporttubesandsecure withfour
mountingscrews.
2. Alignseatsupporttubeswiththefourchannelguidesontheunderside
oftheframeandslidethemthroughthechannelguidesuntilthesnap
buttonsfu llyprotrudethroughthechannelgu ide holes.
NOTE:Anaudibleʺclickʺwillbe
heard.
Assembly, Installation and Operating Instructions
Attaching the Seat Pads/Seat
Performthefollowingdep endingonbenchtype:
Model9670(DETAIL“A”) :
1. P ositiontheseatandlegframestogetherupside downonalev elsurface
(snapbuttonsfacing inward).
2. Attachthelegframestotheseatwithmountingscrews.
Othertransferbenchmodels(DETAIL“B”):
1. P ositiontheseatpadsandlegframestogetherupside
downonalevel
surface.
2. Securetheendrailtothelegframewith theshortmountingscrewsand
locknuts.
3. RepeatSTEPS1‐2toattachtheotheren drailontheoppositeen dofthe 
legframes.
4. Alignthemountingholesintheseatpadswiththemountingholesin the
leg
framesandattach withmountingscrews.
Attaching the Seat Arm
Performthefollowingdep endingonbenchtype:
Model9670(DETAIL“A”) :
1. Ontheendofthetransferbenchwith thesoapdish,removeandretain
thehardwa rethatsecurestheseattothelegframe.
2. P ositiontheseatarmagainstthelegframeandinto theslotsinthe seat.
Threadthe
mountingscrewsthroughtheseatarm,thelegframeandthe
seatsupport.Se cu re allinplacewithtw o locknuts.
Othertransferbenchmodels(DETAIL“B”):
1. Removeandretainthehardwarethat securestheendrailtotheleg
frame.
2. P ositiontheendrailagainstthelegframe. Positiontheseatarm
onthe
outsideofthelegframe.
3. Securetheendrailandseatarmtothelegframewithtw omounting
screwsandlocknuts.
4. Model98071only:
•Toinstalltheseatarm, pushthesnapbuttonsontheseatarmand
insertintothebrackets.Makesurethatthesnapbuttonsfully 
protrude
throughtheholesinthebrackets .
NOTE:Anaudibleʺclickʺwillbeheard.
•Toremovetheseatarm,pushthesnapbuttonsinandpullup.
Adjusting Transfer Bench Height
 WARNING
Make sure that all snap buttons protrude fully through the height
adjustment holes in the leg extensions before use, otherwise injury or
damage may occur.
1. Pressthesnapbuttononthelegframe.
2. Slidethelegextensionupordowntothedesiredheightuntilsnap
buttonprotrudesfu llythroughthe heightadjustmentholeintheleg
extension.
NOTE:Anaudibleʺclickʺwillbeheard.
3. RepeatSTE PS 1and2fortheotherlegsasrequired.
Back
Seat Arm
Soap Dish
Leg Extension
Seat
Leg Frame
Tabs (insert into holes in seat)
Back
Support
Seat Arm
Back Support
Tubes
Seat Pads
Snap Button
Height
Adjustment Holes
End
Rail
Leg
Extension
Leg
Frame
Channel Guides
DETAIL “B” - OTHER TRANSFER BENCH MODELS
MODEL 98071
MODEL 9871
Back
Support
Seat Arm
Back Support
Tubes
Seat Pads
Leg
Extension
Height
Adjustment
Holes
Channel Guides
Leg
Frame
End
Rail
Suction
Feet
DETAIL “A” - TRANSFER BENCH MODEL 9670

Invacare 9670 Specifications