Need help?Do you have a question about the Isotherm WHITE and is the answer not in the manual?
Read all warnings before installation/use for safe operation, installation, and maintenance.
Do not remove panels/grids, handle the door carefully, avoid placing objects on vents, and always lift the device.
Disconnect power before maintenance, use only for ice production, and do not use the ice container for food/beverages.
Ensure ventilation grids are unobstructed to maintain performance and prevent device damage.
Avoid wet conditions, bare feet, plug extensions in showers, and improper cable disconnection.
Ensure supervision, avoid modifications, use qualified personnel for maintenance, and contact support for faults.
Make device inoperative, remove door, handle refrigerant safely, and recover materials per local laws.
Ensure proper installation to avoid environmental/personal damage; use life-saver for quay power.
Avoid uncovered cables, direct generator connection, and covering ventilation openings.
Install in suitable room/water temperatures, avoid direct sun/heat; follow placement restrictions.
Use specified screws and the fixing flange; ensure the device is stable and immobile.
Match voltage, ensure grounding, adequate capacity, and use a specific protected socket.
Stretch the power cable fully and ensure damaged cables are replaced by professionals.
Use cold, drinkable tap water only; operating pressure must be between 1 and 6 bar.
Connection by qualified personnel; install a faucet for water flow interruption.
For hard water, install a softener and a mechanical filter, inspect/clean periodically.
Never close the water supply faucet while the device is operating.
Check connections, water supply, and power; turn on the I/O switch.
System self-adjusts; production halts when compartment is full and resumes when emptied.
Ensure water pressure is between 1 and 6 bar and use only cold, drinkable water.
Ensure adequate ventilation for the compressor unit and keep front grid free of obstructions.
Cooling system is sealed; annual maintenance involves cleaning the condenser with a soft brush.
Wash inner parts with mild detergent before first use; rinse well and discard initial ice production.
Check power supply, plug connection, and ensure the I/O start switch is lit.
Verify water supply, pressure, electric valve function, and check for condenser dust or gas leaks.
Check ice make cycle, gas loss, or wiring issues; contact service if problems persist.
If the shut-off arm is blocked/mispositioned, reset it; replace the mechanism if the problem reappears.
Transport and install with two persons; refrigerant is ecological and non-flammable; avoid damaging cooling pipes.
Eliminate fire sources, ventilate in case of refrigerant leakage, and disconnect properly if damaged.
Do not store flammables, avoid sparks, do not use electrical equipment inside, and do not use device parts as supports.
Not for users with impairments unless supervised; monitor children, avoid prolonged cold contact, and do not eat expired food.
Appliance marked with WEEE symbol; do not treat as household waste. Hand over to applicable collection point.
Apparecchio marcato WEEE; non trattare come rifiuto domestico. Consegnare presso punto di raccolta idoneo.
Gerät mit WEEE-Symbol gekennzeichnet; nicht als Hausmüll behandeln. An Sammelstelle abgeben.
Appareil marqué du symbole DEEE/WEEE; ne pas traiter comme déchet ménager. Remettre à un centre de collecte.
Produkt märkt enligt WEEE-direktiv; ej hushållsavfall. Lämna in på lämplig uppsamlingsplats.
Aparato marcado CE/RAEE; no tratar como residuo doméstico. Entregar en punto de recogida para reciclaje.
Apparaat voorzien van AEEA-merkteken; niet als huishoudelijk afval behandelen. Afgeven bij verzamelpunt.
General| Voltage | 220-240V |
|---|---|
| Material | Stainless steel |
| Ice Type | Cube |
| Frequency | 50 Hz |
| Power Supply | 220-240V, 50Hz |
To Next Page
