What to do if Itsumi BT-100 do not pull sleeve?
Ensure the air pressure level is appropriate. The electro magnetic valve may be damaged. Adjust the pressure level of the electro decompression valve for tuck slide in and tuck slide return. Check the electro magnetic valve for tuck slide, replacing it if necessary.
What to do if the power does not come to the switch and operation panel of Itsumi Finishers?
Check the power source cord and your factory's breaker. Investigate and rectify any short circuit issues, then reset the circuit protector.
Why is the fixing of the collar not strong enough on my Itsumi BT-100?
This could be due to worn fixing rubber, air leaking from the cylinder, or a broken/leaking air hose. Try tightening the regulating bolt at the cylinder head. If that doesn't work, replace the fixing rubber or the cylinder packing. Also, inspect the hose for leaks and repair as needed.
What to do if the dummy does not move to the right on Itsumi Finishers?
Check that the devices are returned to the regulate position or enter the command even returned at regulate position. Also, the electro magnetic valve might be damaged, or the start button could be faulty. Check the sensor for release iron, left side of dummy and back of left arm. Inspect the electro magnetic valve for dummy movement and replace it if necessary. Check the start button and replace it if needed.
What to do if Itsumi BT-100 Finishers does not come hot air?
Verify the timer for hot air blowing is properly set. If the thermal relay is activating due to overload capacitance of the hot air motor, remove the cause of the overload capacitance and reset the thermal relay.
How to fix raising stain on Itsumi Finishers?
The pad cover might be stained, or the drying condition might not be sufficient. Replace the pad cover. Increase the finishing timer or strengthen the dehydration process.
How to fix raising small wrinkles where at the sleeve of Itsumi BT-100?
The drying condition might be poor due to insufficient hot air blowing. Check the root valve of the steam and trap, and/or check the filter for the finish timer and clean it if necessary.
How to fix tuck for the sleeve will open in Itsumi BT-100 Finishers?
The timing of hot air entering the sleeve might be too early. Adjust the timer to an appropriate time for hot air blowing, setting the timer to long in this case.
What to do if Itsumi BT-100 Finishers does not start finish timer?
The button for starting the sleeve might be damaged, or the command to shut the trunk iron is not being entered. Check the sleeve button and replace it if necessary. Check the sensor for shutting the trunk iron.
What to do if Itsumi BT-100 Finishers do not press the trunk?
The dummy might not be moving to the right end, or the electro magnetic valve could be damaged. Check the sensor for dummy movement and the right side of the dummy. Inspect the electro magnetic valve for trunk press and replace it if necessary.
Explains the meaning of WARNING, CAUTION, and NOTE symbols used in the manual.
Troubleshooting steps for power issues, including checking power cords, factory breakers, and circuit protectors.
Addresses issues with setting the collar by checking sensors, foot switches, and electro-magnetic valves.
Solutions for weak collar fixing: tighten regulating bolts or replace fixing rubber.
Steps to diagnose and fix vacuum issues: check foot switches, thermal relays, and hose integrity.
Troubleshoots dummy movement issues: check sensors, electro-magnetic valves, and start buttons.
Addresses left arm extension problems: check sensors, electro-magnetic valves for arm revolving.
Solves trunk pressing failures: check sensors, electro-magnetic valves for trunk press.
Provides solutions for cuff setting failures: check buttons and electro-magnetic valves.
Addresses hot air supply issues: check timers, thermal relays, and TUCK OFF switch.
Solutions for tuck pressing failures: check timers and electro-magnetic valves for tuck press.
Diagnoses poor side finishing due to weak or late air bag swelling: adjust timers.
Solutions for trunk wrinkles: replace worn pad and cover, check drying conditions.
Addresses sleeve wrinkles from poor drying: check steam/trap valves and filter timers.
Solutions for stains on pad cover or due to poor drying: make timer longer for finishing.
To Next Page
General