EasyManua.ls Logo

iWeld GORILLA POCKETMIG 235 DP - User Manual

iWeld GORILLA POCKETMIG 235 DP
162 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
CUTTING EDGE WELDING
R
HASZNÁLATI ÚTMUTATÓ
IGBT inverter technológiás
multifunkciós (MIG/MMA/Lift TIG)
hegesztőgép
GORILLA POCKETMIG 235 DP
GORILLA POCKETMIG 240 DP XL

Table of Contents

Questions and Answers

  • L
    lorraine23Aug 16, 2025
    What to do if iWeld GORILLA POCKETMIG 235 DP Inverter has unsatisfactory weld quality with MIG welding?
    • R
      rshermanAug 17, 2025
      If you're experiencing unsatisfactory weld quality with MIG welding on your iWeld Inverter, it could be due to inadequate or poor-quality materials. Try replacing the consumable parts and changing the welding wire or gas cylinder for materials that are adequate or of higher quality. Also, check the gas supply hose, improve the hose connection with fittings, and inspect the condition of quick couplings if the shielding gas flow is inadequate.
  • J
    Jon MitchellAug 19, 2025
    What to do if iWeld GORILLA POCKETMIG 235 DP Inverter has no wire feed but the feeder motor is running?
    • J
      Jason TapiaAug 19, 2025
      If your iWeld Inverter's feeder motor is running but there's no wire feed, the issue might be due to several reasons. First, check the roller pressure and ensure it is set correctly. Second, verify that the roller groove diameter lead is correct; if not, install the correct guide roller. Third, a dirty wire guide in the handle could be the culprit, so clean the wire liner. Finally, if the electrode wire is blocked, replace the contact tip.
  • D
    Deborah DayAug 22, 2025
    What to do if iWeld GORILLA POCKETMIG 235 DP Inverter has unsatisfactory weld quality when MMA welding and the electrode glues to the welded material?
    • C
      Caleb DavidsonAug 22, 2025
      If you're experiencing unsatisfactory weld quality with your iWeld Inverter when MMA welding, and the electrode sticks to the material, it could be due to a few reasons. First, ensure that the welding leads are connected with the correct polarity. Second, the electrode may be damp, so try replacing it. Lastly, if you're powering the welder with a generator or a long extension cord with too small a cable cross-section, connect the device directly to the mains.
  • D
    Darlene GarciaAug 25, 2025
    What to do if iWeld GORILLA POCKETMIG 235 DP's arc does not light?
    • T
      taylorkaitlynAug 26, 2025
      If the arc on your iWeld Inverter does not light, it could be due to a lack of proper ground terminal clamp contact, so improve the ground terminal contact. Another possible cause is a damaged switch in the MIG gun, in that case replace the switch. Also, incorrect connection of the MIG torch to the device may be the reason, so check the condition of the electrical connections handle, and make sure that the pins in the socket are not broken or jamming.
  • H
    Hannah CarlsonAug 27, 2025
    What to do if iWeld GORILLA POCKETMIG 235 DP Inverter has unsatisfactory weld quality for TIG welding?
    • M
      Megan FlynnAug 27, 2025
      If you're getting unsatisfactory weld quality for TIG welding with your iWeld Inverter, start by checking the quality of the materials and consumables used, especially the electrode tungsten and shielding gas. Replace consumable parts and consider replacing the shielding gas with a higher quality one. Also, check the cylinder regulator and gas supply hose, improve the hose connection with fittings, and inspect the condition of quick couplings if the shielding gas does not flow or flows with insufficient intensity.
  • A
    Alyssa JosephAug 30, 2025
    What to do if iWeld GORILLA POCKETMIG 235 DP Inverter's arc is too long and irregular?
    • P
      Phillip BushAug 30, 2025
      If the arc on your iWeld Inverter is too long and irregular, it could be because the welding voltage is too high. Try reducing the welding voltage. Alternatively, the wire feed speed might be too low; in that case, increase the wire feed speed.
  • T
    Tina HillSep 2, 2025
    What to do if iWeld GORILLA POCKETMIG 235 DP Inverter has irregular wire feed?
    • V
      Valerie AlexanderSep 2, 2025
      If your iWeld Inverter has an irregular wire feed, the issue might be a damaged contact tip, so replace it. Another cause could be a dirty or damaged feed roller groove; try cleaning the roller groove or replacing the roller. Lastly, the wire spool might be rubbing against the welder's cover walls, so ensure the wire spool is correctly secured.
  • J
    Jeffrey SandovalSep 5, 2025
    Why iWeld Inverter's arc is too short?
    • M
      Megan GomezSep 5, 2025
      If the arc on your iWeld Inverter is too short, it could be due to the welding voltage being too low. Try increasing the welding voltage. Another possibility is that the wire feed speed is too high, so reduce the wire feed speed.
  • R
    Robert WernerSep 7, 2025
    What to do if iWeld GORILLA POCKETMIG 235 DP displays after turning on the power and the LEDs are off?
    • P
      Philip WrightSep 7, 2025
      If your iWeld Inverter displays something after being turned on, but the LEDs are off, the issue may be due to no power supply. Check the fuses on the connection network.
  • R
    rhonda72Sep 10, 2025
    What to do if iWeld GORILLA POCKETMIG 235 DP Inverter has no power, failure signal or device malfunction?
    • B
      brownalyssaSep 12, 2025
      If your iWeld Inverter shows no power, a failure signal, or malfunctions, the issue might be due to no connection or a loose plug inside the device. Check and correct the connections of all electrical plugs inside the device.

iWeld GORILLA POCKETMIG 235 DP Specifications

General IconGeneral
Output Current235A
Output Current Range30-235A
Duty Cycle60%
Duty Cycle @ 235A60%
Protection ClassIP21S