JABSCO 37010-4092 - User Manual

Model 37010-Series
Model 37010-Series
ELECTRIC MARINE TOI LET
Push Button Operation
FEATURES
• White Vitreous China Bowl Available in Two Sizes
• Baked enamel seat & cover -
soft close seat option available on regular bowl models
• Flexible Impeller Flush Pump
• Permanent Magnet Type Motor, Fully Enclosed, with
Stainless Steel Shaft
• High Capacity Waste Macerator and Bowl discharge Pump
• Built-in Back Flow Preventer
•
V
Corrosion resistant material for marine use
ARIATIONS
MODEL NUMBER DESCRIPTION
37010-3092 Compact Bowl 12V
37010-3094 Compact Bowl 24V
37010-4092 Regular Bowl 12V
37010-4192 Regular Bowl 12V, Soft Close Seat/Lid
37010-4094 Regular Bowl 24V
37010-4194 Regular Bowl 24V, Soft Close Seat/Lid
INSTALLATION
The Jabsco electric toilet may be installed above or below
the waterline. Flush pump is self-priming with a vertica
l lift
up to 4 feet; discharge macerator pump can operate
against a vertical head up to 4 feet (1.2m).
Inlet and outlet seacocks should be easily accessible and
be positive shut off valves. If seacocks cannot be con ve -
nient ly operated from toilet location, install suitable shut off
valves for inlet and discharge connections.
Base assembly may be moved 90° to accommodate con -
nec tions and provide accessibility fo
r servicing.
Surface where toilet is mounted should be flat to prevent
distortion of toilet base.
PLUMBING CONNECTIONS - Connect inlet hose using
3/4" (19mm) ID hose. Make sure all inlet connec-tions
are airtight and free of sharp bends or restrictions.
Do not connect the toilet to the vessels
potable water for its source of supply. To do so can result in
contamination of potable water supply. If fresh water is pre-
ferred for flushing, provide a separate fresh water tank to
supply water to the toilet only.
DO NOT CONNECT INLET HOSE TO A PRESSURIZED
WATER SYSTEM.
Flood hazard. If toilet is installed below the
waterline or may be below the waterline at any
angle of heel or trim, it must be installed with
properly positioned vented loops. Failure to do
so can result in flooding which can cause loss
of property and life.
WARNING
!
CAUTION
!
Connect 1" (25mm) or 1-1/2" (38mm) hose to discharge
hose to discharge port (Adaptor98023-0080 is included to
convert discharge port to 1-1/2"ID hose), and make
suitable connection to holding tank orother discharge
system. Avoid sharp bends or restrictions.For above
waterline installations, a check valve may haveto be instal-
led in the flush water intake line to ensure rapidpump
priming. To retain water in bowl, make a loop in thedischar-
ge line about 8 inches (200mm) above base of bowl.
If the toilet is, or can be, below waterline at any normal(in-
cluding static) attitude of vessel heel and/or trim, a 3/4"
(19mm) Vented Loop Fitting must be installed in the
length of hoseconnecting the flushing pump to the inlet
seacock. TheVented Loop Fitting must be positioned so it
remains at least 8" (200mm)* above the waterline at all
angles of heel and trim.In some installations when a
vented loop is installed in theintake hose, the flushing
pump primeability and flow char-acteristics are reduced
and may adversely affect toiletfunction. To restore pump
performance, connect a solenoidvalve (Jabsco No.
37068-0000) to the vent air inlet to inter-rupt the air
supply during the flush cycle. The brass port ofthe
solenoid valve (remove plastic filter if attached)shouldbe
connected to the vent inlet with 3/16" hose and thesole-
noid wired in parallel with the toilet motor. See diagram
below.

Summary

Features and Variations

Features

Key features of the electric marine toilet system, including bowl size options and pump capabilities.

Variations

Details on available model numbers and their corresponding descriptions, including bowl size and seat options.

Installation and Safety

Plumbing Connections

Guidance on connecting inlet and discharge hoses, including hose size and bend restrictions.

Important Cautions

Safety warnings regarding water levels, potable water connections, and vented loop requirements.

Electrical and Operation

Electrical Connections

Instructions for connecting the toilet's electrical system, including wiring and power source requirements.

Operating Instructions

How to operate the toilet, including flushing, waste handling, and safety measures.

Disassembly

Step-by-step instructions for disassembling the electric marine toilet for maintenance or repair.

Parts and Dimensions

Exploded View and Parts List

A comprehensive list of all parts for the electric marine toilet with an exploded view diagram.

Dimensional Drawing

Diagram illustrating the physical dimensions of the toilet and its components.

Warranty Information

JABSCO 37010-4092 Specifications

General

Brand	JABSCO
Model	37010-4092
Category	Toilets
Language	English