Name: JAMEC PEM TDR3000
Brand: JAMEC PEM
Rating: 5 (1 reviews)

To Next Page

To Previous Page

TYRE INFLATOR

DIGITAL TDR3000

The Jamec Pem TDR Digital Tyre Inator represent quality and guaranteed

accuracy. The classic handheld, slimline design is easy to hold and is

designed to last in rugged workshop environments.

FEATURES

 Includes Certicate of calibration

 Multi-scale gauge

 Large backlit digital display

 Accuracy exceeds EC Standards

 Auto on upon pressure sensing

 Auto off after 9 seconds

 Tough die-cast aluminium housing

 Wire sheathed hose eliminates kinking

 Impact absorbing bumpers

 Rubber grip on chuck

MAINTENANCE MONTHLY

Remove the ‘oil’ screw on the side of the gauge and place 2-3 drops of

‘light’ oil into the gauge mechanism.

IMPORTANT

This tyre inator must only be connected to air line systems which have

clean dry air. Any moisture in the air line system may cause damage to

the operation of this tyre inator and void warranty.

Air pre-lters must be used with this inator to ensure product accuracy

and longevity.

OPERATION

TO READ PRESSURE:

Remove tyre valve cap. With clip-on air chuck lever depressed, rmly press

chuck onto tyre valve stem and release lever, ensure that no air leaks.

Check pressure gauge.

Digital - the digital display will activate once the tyre pressure is sensed.

If no pressure is sensed the display will not turn on. Press the tyre inator

lever to add air into the tyre, before reading the pressure.

DIGITAL - the dial gauge will activate once the tyre pressure is sensed. If

no pressure is sensed ,press the tyre inator lever to add air into the tyre,

before reading the pressure.

TO INFLATE:

With clip-on air chuck lever depressed, rmly press chuck onto tyre

valve stem and release lever, ensure that no air leaks. Fully depress the

tyre inator lever for an appropriate period of time and release the lever.

Checkpressure gauge and repeat the procedure until correct pressure level

is achieved.

TO DEFLATE:

With clip-on air chuck lever depressed, rmly press chuck onto tyre valve

stem and release lever, ensure that no air leaks. Depress the tyre inator

lever half way (until air can be heard to be escaping) for an appropriate

period of time and release the lever. Check pressure gauge and repeat the

procedure until correct pressure level is achieved.

SAFETY

Never exceed the maximum pressure of the tyre. Check that the hose and

chuck are in good condition with no damageorcracks. Ensure safe working

environment when using compressed air. Return to authorised service agent

for repair and maintenance.

WARNING

To avoid risk of personal injury, especially to the eyes, face and skin

DONOT direct the air stream at any person, or any part of the body.

Thisequipment is not intended for use by children without adult

supervision. The manufacturer reserves the right to change product

features at any time without notice.

SPECIFICATIONS

Part No. 10.3012 10.3012OS

Operation

Inate / deate / measure Inate / deate / measure

Supply pressure max.

200 psi 200 psi

Max. inflation

174 psi 174 psi

Chuck type

Hold on Hold on

Chuck style

Dual angle Dual angle

Scale

psi, kPa, bar psi, kPa, bar

Inlet size

1/4" BSP 1/4" BSP

Hose length

500mm 500mm

Accuracy

± 2 psi @ 25 - 75 psi ± 2 psi @ 25 - 75 psi

Inflation volume L/min

500 L/min @ 188 psi 500 L/min @ 188 psi

Power source

2 x AAA (included) 2 x AAA (included)

Battery life (continuous use)

80 hr 80 hr

Auto off 9 sec 9 sec

Weight .85 kg .85 kg

Advised application Industrial, workshops Industrial, workshops

Packaging Jamec Pem Box Jamec Pem Box