Jata electro BT1041 - Blender Operation and Maintenance; Instructions of Use; Maintenance and Cleaning; Environment Protection

9
• Make sure neither the appliance nor the cables are in direct
contact with hot surfaces or objects.
• Always place it on a at surface.
• Always disconnect it from the mains when you do not use it and
before assembling / disassembling or when cleaning.
• Take all necessary precautions while handling the blade, as it is
very sharp.
• The cleaning and maintenance done by user can not be done by
children without any supervision.
• If the cable were to deteriorate it must be changed by an
Authorised Service Centre.
INSTRUCTIONS OF USE
• Placethejug(3)onthemainbody(4).Nextturnthejugclockwisetilltheendtoleaveitcorrectlyxed.(Fig.A).
• Pourthefoodinthejugandplacethelidonit.Makesuretheblenderisperfectlyclosedandmaintainalways
heldwhileinuse.
• Plugtheapplianceintothemains.Theringwilllightup(6).Thisringwillstayalwaysonwhentheblenderis
connectedtothemainsandthejuginserted.
• Turnthespeedselector(5)clockwisetothedesiredposition(1to5).Theblenderwillbegintoworkmaintaining
theselectedspeed.
• Itisadvisabletobeginatthelowestspeedoftheblendertolaterraisethehighestspeed(position5)ifnecessary.
However,anddependingonthetextureofthefood,youmayusethehighestspeedfromthebeginning.
• Theposition“PULSE”isidealtocrushtheice.Turnthebuttonandreleasetheselectorrepeatedlyforperiodsof
about2secondstogetcrushedice.Forit,wesuggesttouselittleicecubes,oryoucanbitthembeforeputthem
ontheblender,toavoidthe“igloo”eect.Thismeansthatthecrushedicegetsadheredtotheblenderwalls,and
itimpedethattheothericecubesarrivetothebasetobecrushed.
• Youmayaddingredientstothejugwhileinusewithoutopenthelid.Duringoperationofthemixer,ingredients
maybeaddedwithoutremovingthelid.Todothis,removethestopper(1).Slowlyaddtheingredientsthrough
theopeninginthelidandplacethecapagain.
• Onceyouhavenished,setthespeedselectortoits“0”positionandwaitforthebladetostopturningcompletely
beforeremovingthejug.
MAINTENANCE AND CLEANING
• Beforeyouproceedtocleaning,makesuretheapplianceisunpluggedfromthemains.
• Youcanremovethebladeforcleaningbyperformingthefollowingsteps:
- Placethejarupsidedown.
- Removethering(7)byturningitclockwise.Directionindicated“OPEN”.
- Removethebladeblock(8).
- Holdtheknifewithyourhandandturnthetransmissionclockwise.
• Thejar,thelid,thecapandtheothercomponentsofthejarcanbecleanedwithsoapandwater,neverinthe
dishwasher,tryingtorinseanddrythemwell.
• Cleanthemainbodywithaslightlydampcloth.
• Donotuseabrasiveorchemicalproducts,suchasmetallicscourers,whichmaydeterioratethesurfacesofthe
appliance.
• Oncecleaned,assemblythejarbyreversingtheabovestepsandtakingtheprecautionthatallcomponents,
siliconering(9)andwashersareintheiroriginalpositionandturntheringinthedirectionindicated“CLOSE”.
ENVIRONMENT PROTECTION
• Disposetheapplianceaccordingtothelocalgarbageregulations.
• Neverthrowitawaytotherubbish.Soyouwillhelptotheimprovementoftheenvironment.
01 manual jata BT1041.indd 9 12/07/17 17:29