Why can't client software view Jaycar Electronics DS-8704HI-S DVR live image?
The client software might not be able to view the live image from your Jaycar Electronics DVR due to a network error. Another possible reason is connecting to the wrong DVR with an incorrect IP address, port number, username, or password. Make sure your network is working correctly and that you're using the correct DVR connection details.
What to do if Jaycar Electronics DS-8704HI-S DVR cannot find the hard disk in reboot process?
If your Jaycar Electronics DVR cannot find the hard disk during the reboot process, it could be due to a broken hard disk cable. Consider replacing the hard disk cable. Another potential reason is that the hard disk's power cable isn't connected; ensure it's properly connected. Lastly, the hard disk itself might be broken, requiring a replacement.
Why does my Jaycar Electronics DS-8704HI-S continuously reboot and make a 'di' sound?
Your Jaycar Electronics DVR might be continuously rebooting and making a 'di' sound due to several reasons: * You may have upgraded the DVR with the wrong firmware. In this case, upgrade to the correct firmware. * The compression board could be faulty, requiring a replacement. * The main board might have issues and need to be replaced.
How to fix Jaycar Electronics DS-8704HI-S DVR when it can't control PTZ through RS-485 port?
If your Jaycar Electronics DVR cannot control PTZ through the RS-485 port, check the following: * Ensure the RS-485 cable is correctly connected and not broken. If it's broken, replace it. * Verify that the PTZ parameters are correct and adjust them if necessary. * The RS-485 port of the DVR might be broken, requiring a replacement.
What to do if there are no images on the monitor connected to Jaycar Electronics DS-8704HI-S?
If there are no images on the monitor connected via VOUT after starting your Jaycar Electronics DVR, the issue could be with the cable connecting the monitor. Try replacing the cable. Alternatively, the real board or the main board of the DVR might be faulty, requiring replacement.
Why isn't the fan working on my Jaycar Electronics DS-8704HI-S DVR even though the power light is green?
If the "POWER" light on your Jaycar Electronics DVR's front panel turns green but the fan doesn't work, it could be due to a broken front panel cable, which would need to be replaced. Another possibility is that the fan itself is broken and needs replacing.
Why does the fan not work on my Jaycar Electronics DVR when the power light is green?
If the "POWER" light turns green and the indicator lights turn on, but the fan doesn't work on your Jaycar Electronics DVR, it's possible that the ATX plug in the main board is not well plugged in. Try re-plugging the ATX plug into the main board.
How to troubleshoot Jaycar Electronics DVR when the power light doesn't turn on?
If the "POWER" light on the front panel of your Jaycar Electronics DVR doesn't turn on and the fan doesn't work after plugging in the power and turning on the switch, the power cable may be broken. In this case, replace the power cable. Another possible cause is a broken power supply, which would also need to be replaced.
What to do if there is no response in HyperTerminal interface of Jaycar Electronics DVR?
If there is no response in the HyperTerminal interface, the baud rate might not be matched. Set the correct baud rate. Alternatively, the RS-232 cable could be broken, requiring a replacement. Also, the serial port of your PC or the RS-232 port of the DVR might be broken, and you may need to replace them.
General| Hard Drive Capacity | Up to 6TB |
|---|---|
| Channels | 4 |
| Compression | H.264 |
| Video Input | 4 channels |
| Audio Output | 1 channel |
| Hard Drive Support | 1 SATA |
| Network Interface | RJ45 |
| USB Interface | 2 USB ports |
| Power Supply | DC 12V |
| Operating Temperature | -10°C to +55°C |
To Next Page
