JessEm Tool Mast-R-Lift 02101 User Manual

User Manual
Model #02101, 02102
Thank you for choosing this product from
JessEm Tool Company. We appreciate your
support and hope that our product serves you
well. This product is designed to provide
many years of reliable service provided it is
used as intended and taken care of.
This user manual will assist you in assembly
and general operation of this product. It is
not our intent to teach you about
woodworking. It is assumed that you are an
experienced woodworker with the basic skills
and experience necessary to use this product
safely. If after reading the following
instructions, if you are unsure or
uncomfortable about safely using this
product we urge you to seek additional
information through widely available
woodworking books or classes.
As part of our Continuous Product
Improvement Policy, JessEm products are
always advancing in design and function.
Therefore there may be differences between
what is shown in our catalogs, website or at
retail display and what is sold at time of
purchase. We reserve the right to make
positive changes to our products at our
discretion.
Suggested Router Bit Speeds
Bit Diameter Max. Speed
1” (25mm) 24,000 RPM
1-1/4” - 2” (30-50mm) 18,000 RPM
2-1/4” - 2-1/2” (55-65mm) 16,000 RPM
3” - 3-1/2” (75-90mm) 12,000 RPM
124 Big Bay Point Road
Barrie, Ontario, L4N 9B4
Canada
866-272-7492 Toll Free
705-726-6145 Local Phone
705-726-6055 Fax
Email: jessem@jessem.com
Website: www.jessem.com
IMPORTANT!
Read and understand the contents of
this manual before assembly or
operation of this product.
Mast LiftR
CONTENTS:
1-Mast-R-Lift
1-Height Adjustment Handle
Also includes 1-Insert Ring, 1-Insert Ring
Wrench, 1-1/8” Hex Wrench, 1-Start Pin
TOOLS REQUIRED FOR ASSEMBLY:
5/16” Hex Wrench
TOOLS REQUIRED FOR ADJUSTMENT:
7/16” Wrench

JessEm Tool Mast-R-Lift 02101 Specifications

General

Product Type	Router Lift
Model Number	02101
Table Opening Size	9-1/4" x 11-3/4"
Material	Anodized Aluminum
Plate Dimensions	9-1/4" x 11-3/4"
Lift Travel	3-1/2"
Anodized Aluminum	Yes
Brand	JessEm
Compatibility	Most Routers
Precision Adjustment	Yes
Mounting Plate Included	Yes

Summary

Safety and Precautions

General Safety Precautions

General safety advice for operating power tools, including reading manuals and using protective gear.

Specific Warning: Cordless Drill Usage

Prohibits using a cordless drill for lift carriage adjustment to prevent wear and warranty void.

Router Safety Precautions

Safety guidelines for using the router itself, such as bit insertion and feed rates.

Router Installation

Placing the Crank Handle

Instructions for inserting and using the crank handle for initial carriage positioning.

Mounting the Router Motor

Steps to loosen the clamp, slide the motor into the carriage, and position it correctly.

Custom Router Table Installation

Adapting to Custom Table Ports

Guidance for fitting the lift into custom-made router table openings, mentioning templates.

Adjusting Table Port Fit

Using adjustable snugger bars to ensure a tight fit of the lift plate in the table opening.

Insert Ring System

Insert Ring Installation and Removal

How to install, tighten, and loosen insert rings using the provided wrench.

Lift Adjustment and Operation

Leveling the Lift in the Table Top

Using plate levelers to ensure the lift surface is flush with the router table surface.

Using Your Mast-R-Lift

Height Adjustment Mechanism

Detailed instructions on how to raise and lower the router using the adjustment handle.

Thread Tension Adjustment

Procedure to reset thread tension if the bit height changes during use.

Limited Warranty Information

JessEm Tool Limited Warranty

Details the product warranty, claim process, and responsibilities of the consumer.

Warranty Limitations

Lists conditions and actions that are not covered by the product warranty.