JML Finishing Touch Flawless

To Next Page

Thank you for your purchase of Finishing Touch® Flawless®, the easy and convenient facial hair remover.

Installing / Changing Battery

• Remove the Finishing Touch® Flawless® cap (Image 1).

• Grab the upper section of the unit with one hand, the bottom half with the

other, and pull apart (Image 2) to reveal the battery chamber.

• Place 1x 1.5V AA alkaline battery (not included) into the compartment, making

sure the positive pole (+) is facing the bottom of the unit.

• Slide/snap the unit’s bottom casing back into place (Image 2).

Battery Safety and Information

• Non-rechargeable batteries are not to be recharged.

• Rechargeable batteries are only to be charged under adult supervision.

• Rechargeable batteries are to be removed from the product before being charged

dierent types of batteries or new and used batteries are not to be mixed.

• Batteries are to be inserted with the correct polarity.

• Always make sure the battery compartment is secure.

• Exhausted batteries are to be removed from Finishing Touch® Flawless®.

• The supply terminals are not to be short-circuited.

How to Use

• Remove the Finishing Touch® Flawless® cap (Image 1).

• Slide the switch located on the side of the unit upward into the “ON” position

(Image 3). The light will automatically turn on when the unit is “ON”.

• Gently press the head of the unit at against your skin. The unit should not be on an

angle. Proceed making small circular motions to remove unwanted hair (Image 5).

NOTE: It is normal for the head to become warm with use.

Cleaning (be sure unit is o)

• Twist the rotating hair removal head counter-clockwise and lift o (Image 4).

• After each use, clean the head by using a brush (included) to wipe away the hair residue.

• Empty any hair from the body of the Finishing Touch® Flawless® unit by turning

it over and gently tapping the sides.

• To put the hair removal head back on the unit, line up the “groove” indicators on

the cap with those on the unit and twist clockwise (Image 4).

Tips & Pointers

• For superior results, use on hair ¼" in length or less.

• If the unit begins to slow down, clear the hair removal head and body of any hair

residue. If the unit is still running slow change the battery.

• Gentle enough to use every day.

• For airbrush-like make-up application, use daily.

NOTE: Prior to rst use, test the Finishing Touch® Flawless® on a small area. If any

sensitivity or allergic reactions occur, discontinue use immediately. Do not use

your Finishing Touch® Flawless® on sensitive or irritated skin.

Replacement Head

For optimal results it is recommended that you replace your Finishing Touch®

Flawless® head every 6 months. The head may need to be replaced sooner if the

Finishing Touch® Flawless® loses performance or if the head becomes chipped or

damaged in any way. Please contact JML customer services for replacement heads.

IMAGE 1

IMAGE 3

IMAGE 5

IMAGE 2

IMAGE 4

Warnings

• Keep out of reach of children.

• This is not a toy. Children shall not play with this product.

• Do not use on irritated skin. Discontinue use if skin

irritation occurs.

• Do not use on sensitive eye areas. Do not use on eyelashes.

• Avoid direct eye exposure. Do not look directly into light

during use.

• Do not rinse trimmer head under water.

• Do not submerge unit under water.

• Store in a cool dry place when not in use.

Need help?

Do you have a question about the JML Finishing Touch Flawless and is the answer not in the manual?

Summary

Installing and Changing Battery

Battery Safety Information

How to Use the Facial Hair Remover

Operating the Device

Slide the switch to 'ON'. The light turns on. Gently press the head flat against skin and use small circular motions.

Cleaning and Maintenance

Cleaning the Head

Twist head counter-clockwise, lift off, and use brush to remove hair residue. Tap unit to empty body.

Reattaching the Head

Align 'groove' indicators and twist head clockwise to reattach.

Usage Tips and Pointers

Optimal Hair Length

For superior results, use on hair 1/4" or less. Test on a small area first.

Performance Issues

Clear hair residue if unit slows. Change battery if still slow. Gentle enough for daily use.

Replacement Head Recommendation

Important Warnings

Safety Precautions

Keep away from children. Do not use on irritated/sensitive skin or eyelashes. Avoid eye exposure.

Water Usage Restrictions

Do not rinse trimmer head or submerge unit under water. Store in a cool, dry place.

Quick Start Guide Steps

Step 1: Remove Cap

Remove the protective cap from the device.

Step 2: Install Battery

Pull the unit apart, insert AA battery with correct polarity, and reassemble.

Step 3: Turn Unit On

Slide the gold switch upward to turn the unit on.

Step 4: Remove Hair

Use the device in a circular motion on the skin to remove unwanted hair.