john deer S780 - Page 11

Contents
Page
Header Reel/Belt Pickup Pump
Belt (Variable Speed Feeder
House)—Replacing ......................................55-19
Header Reel/Belt Pickup Pump
Belt (Variable Speed Feeder
House)—Adjusting .......................................55-24
Feeder House Fixed Speed Drive
Belt—Replacing ...........................................55-24
Feeder House Fixed Speed Drive
Belt—Adjusting.............................................55-25
Header Reel/Belt Pickup Pump Belt
(Fixed Speed Feeder House)—Replacing ...55-25
Header Reel/Belt Pickup Pump Belt
(Fixed Speed Feeder House)—Adjusting ....55-28
CommandTouch Multi-Speed Feeder
House Drive Belt—Replacing.......................55-28
CommandTouch Multi-Speed Feeder
House Drive Belt—Adjusting........................55-29
Header Reel/Belt Pickup Pump Belt
(CommandTouch Multi-Speed
Feeder House)—Replacing..........................55-29
Header Reel/Belt Pickup Pump Belt
(CommandTouch Multi-Speed
Feeder House)—Adjusting...........................55-31
Manual Tilt Indicator (Lateral Tilt System) ........55-31
Attach Multi-Coupler and Single Point
Latching........................................................55-32
Attaching and Detaching Header from
Feeder House ..............................................55-35
Single Point Latching—Adjusting .....................55-36
Level Land Feeder House Lower Cable
End—Adjusting ............................................55-38
Level Land Feeder House—Shim Adjusting.....55-38
Feeder House Latching Pins (Cleanout) ..........55-39
Feeder House Manual Unlatching ....................55-39
Shear Screw Location ......................................55-39
Shields
Gull Wing Doors .................................................60-1
Gull Wing Door Cylinder Adjustment..................60-2
Left-Hand Side Shields.......................................60-2
Right-Hand Side Shields ....................................60-4
Separator Covers ...............................................60-5
Separator
Standard Feed Accelerator Wear
Strips—Replacing ..........................................65-1
Tough Crop Feed Accelerator Wear
Strips—Replacing ..........................................65-2
Tine Feed Accelerator Wear Strips—Replacing ..65-3
Tine Feed Accelerator Comb Floor
(Rice Machines) .............................................65-4
Tine Feed Accelerator Comb Floor
(Rice Machines)—Removing .........................65-4
Feed Accelerator Belt—Replacing .....................65-7
Feed Accelerator Belt—Adjusting.......................65-9
Page
Standard Speed High Capacity Feed
Accelerator—Changing Speed.......................65-9
High Speed High Capacity Feed
Accelerator—Changing To Slow Speed .......65-10
Concave Recommendations ............................65-10
Concave Types................................................. 65-11
Separator Grate Spacers.................................. 65-11
Separator Grate Types .....................................65-12
Separator Grate Covers (If Equipped)..............65-12
Separator Grate Interrupters (If Equipped).......65-13
Separator Grate Interrupter Locations
(If Equipped).................................................65-13
Concave Sector Gear Shear Bolts
(Standard Concave Adjust) ..........................65-14
Concave Sections (Standard Concave
Adjust)—Remove and Install........................65-14
Concave Sections (Active Concave
Isolation)—Remove and Install ....................65-19
Concave Leveling (Standard Concave
Adjust) ..........................................................65-28
Concave Leveling (Active Concave Isolation) ..65-31
Separator Top Cover Vanes (If Equipped)........65-38
Threshing Elements and Tines
(TriStream Rotor)—Remove and Install .......65-38
Threshing Element and Separator
Tine Location (TriStream™ Rotor
Standard Configuration) ...............................65-40
Threshing Element and Separator Tine
Location (TriStream Rotor Tough
Grain Configuration).....................................65-41
Threshing Element and Separator Tine
Location (TriStream Rotor Dense
Pack Configuration)......................................65-42
Threshing Elements and Tines
(Variable Stream Rotor)—Remove
and Install.....................................................65-43
Threshing Element and Separator Tine
Location (Variable Stream Rotor
Standard Configuration) ...............................65-46
Threshing Element and Separator Tine
Location (Variable Stream Rotor
Dense Pack Configuration) ..........................65-47
Posi-Torq™ Separator—Dual-Range ...............65-48
Separator Drive Sheave Gap—Adjusting .........65-49
Separator Variable Drive Belt—Replacing........65-50
Auger Bed Dividers...........................................65-50
Discharge Beater Belt—Adjusting ....................65-51
Discharge Beater Belt—Replacing ...................65-51
Discharge Beater Wear
Strips—Replacing (5 and 10 Wing Style).....65-56
Standard Discharge Beater Wear
Strips—Replacing (8 Wing Style).................65-57
Tough Crop Discharge Beater Wear
Strip—Replacing ..........................................65-58
Overshot Beater Belt (If
Equipped)—Adjusting ..................................65-58
Continued on next page
vii
070717
PN=7