To Next PageTo Next Page
Need help?Do you have a question about the John Lewis Balance and is the answer not in the manual?
Follow regulations, switch off power, use correct bulbs, and handle hot parts carefully. For indoor use only.
Clean with a soft dry cloth. Replace bulbs with compatible types. Handle carefully.
Remove mounting bracket, mark and drill holes, attach bracket securely to the wall.
Connect supply wires to terminals (Live to L, Neutral to N). No Earth connection required.
Install bulb, fit shades carefully, do not overtighten. Restore power after completion.
Follow regulations, switch off power, use correct bulbs, and handle hot parts carefully. For indoor use only.
Clean with a soft dry cloth. Replace bulbs with compatible types. Handle carefully.
Remove mounting bracket, mark and drill holes, attach bracket securely to the wall.
Connect supply wires to terminals (Live to L, Neutral to N). No Earth connection required.
Install bulb, fit shades carefully, do not overtighten. Restore power after completion.
This document describes the Balance 2Lt Wall Light, a lighting fixture designed for indoor use.
The Balance 2Lt Wall Light is a decorative and functional lighting solution intended to illuminate interior spaces. It features two light sources, providing ambient or task lighting depending on its placement and the chosen bulbs. The design emphasizes ease of installation and safe operation, with clear instructions provided for both setup and ongoing maintenance.
The wall light is designed to be permanently installed on a wall surface. Before installation, users must ensure the house electricity supply is switched off at the fuse box to prevent electric shock. The mounting bracket is first attached to the wall, ensuring it is firmly fixed into a solid or suitable mounting surface, not just plasterboard. Care must be taken to avoid damaging existing wiring during this process.
Electrical connections are made by connecting the supply live wire (typically brown or red) to the fitting's live terminal (marked "L") and the supply neutral wire (typically blue or black) to the fitting's neutral terminal (marked "N"). It is crucial to note that NO EARTH connection is required for this Class II product. Users are advised to consult a qualified electrician if unsure about correct polarity, as residential wiring can vary. All electrical connections must be tight, with no loose strands of wire protruding from the terminal block, before the connector block cover is snapped back into place.
Once the electrical connections are secure, any excess cable should be carefully located inside the ceiling cup or within the ceiling cavity. The fitting is then offered over the mounting bracket and secured in place using the screws and washers previously removed.
The Balance 2Lt Wall Light requires two 3-5 Watt G9 energy-efficient LED bulbs. Users must ensure they fit the correct bulb type and wattage as indicated in the specification table, and the indicated wattage must not be exceeded. After fitting the bulbs, the shades are attached by placing the threaded hole in the shade over the lamp holder section and rotating them into place. Care should be taken not to overtighten the shades, as this may cause damage to the fitting.
Once installation is complete, the house electricity supply can be restored at the fuse box, and the light can be switched on.
Regular maintenance of the Balance 2Lt Wall Light is straightforward and primarily involves cleaning and bulb replacement.
For cleaning, it is recommended to use a soft, dry cloth. Abrasive materials should not be used, as they can damage the finish of the product.
When replacing bulbs, users must always switch off the mains electricity supply and allow the old bulb to cool down before handling. Used bulbs should be disposed of carefully and responsibly. The product uses 2 x 3-5 Watt G9 energy-efficient LED bulbs. Replacement bulbs should be sourced from John Lewis or an established brand of the same type and compatibility.
The device is designed for longevity, but should any parts be damaged or missing, users are advised to contact lightingparts@JLPspares.co.uk via email.
Troubleshooting guidance is provided for common issues. If the light does not work when switched on, users should first check if the power supply is switched on. If the power is on, the light should be turned off, and the bulb's insertion should be checked for correctness. Finally, the bulb itself should be checked to ensure it is still in working order.
The product is marked with a symbol indicating that it should not be treated as normal household waste. Instead, it should be recycled. John Lewis, as a member of the Distributer Take Back scheme, has contributed to the development and upgrade of recycling facilities across the UK. Users can take the product to their nearest collection facility or contact their local council for further details, or visit www.recycle-more.co.uk for more information on responsible disposal.
It is important to retain the instruction manual for future reference, as it contains crucial information for safe and satisfactory operation and maintenance of the Balance 2Lt Wall Light.
General| Product Type | Table Lamp |
|---|---|
| Material | Metal |
| Colour | Brass |
| Bulb Included | Yes |
| Height | 40cm |
| Width | 20cm |
| Weight | 1.5kg |
| Bulb Type | LED |
| Cable Length | 1.5 m |
| Switch Type | In-line |
