John Lewis Eyelet Curtain Pole Kit

Other manuals for John Lewis Eyelet Curtain Pole Kit

Instruction Manual2 pages

Need help?

Do you have a question about the John Lewis Eyelet Curtain Pole Kit and is the answer not in the manual?

Summary

Pre-assembly Preparation

Necessary Tools

Lists essential tools required before starting assembly of the curtain pole kit.

Fittings and Parts Checklist

Quantities Required

Details the specific number of parts needed for different pole lengths and bracket configurations.

Recommended Maximum Curtain Weights

Step-by-Step Assembly Instructions

Step One: Measure Windows

Guide on measuring windows and determining bracket placement for the curtain pole.

Step Two: Wall Mounting Plates

Instructions for marking, drilling, and fixing wall mounting plates to the wall.

Step Four: Cutting the Pole

Procedure for calculating and cutting the curtain pole to the desired length.

Step Five: Joining Poles

Method for joining two pole sections using a connector piece for longer installations.

Step Six: Curtain Placement

Guidance on sliding curtains onto the pole before fitting it into the brackets.

Step Eight: Fitting the Finial

Instructions on attaching the decorative finial to the end of the curtain pole.

Step Nine: Test Installation

Final step to check the installed pole by drawing curtains across it.

Summary

Pre-assembly Preparation

Necessary Tools

Lists essential tools required before starting assembly of the curtain pole kit.

Fittings and Parts Checklist

Quantities Required

Details the specific number of parts needed for different pole lengths and bracket configurations.

Recommended Maximum Curtain Weights

Step-by-Step Assembly Instructions

Step One: Measure Windows

Guide on measuring windows and determining bracket placement for the curtain pole.

Step Two: Wall Mounting Plates

Instructions for marking, drilling, and fixing wall mounting plates to the wall.

Step Four: Cutting the Pole

Procedure for calculating and cutting the curtain pole to the desired length.

Step Five: Joining Poles

Method for joining two pole sections using a connector piece for longer installations.

Step Six: Curtain Placement

Guidance on sliding curtains onto the pole before fitting it into the brackets.

Step Eight: Fitting the Finial

Instructions on attaching the decorative finial to the end of the curtain pole.

Step Nine: Test Installation

Final step to check the installed pole by drawing curtains across it.

This document provides instructions for the installation and maintenance of the John Lewis Eyelet Curtain Pole Kit.

Function Description:

The John Lewis Eyelet Curtain Pole Kit is designed to support eyelet and tab-top curtains. It consists of poles, brackets, finials, and a joiner (for longer lengths), allowing for the secure hanging and smooth movement of curtains across a window. The kit is available in two standard lengths: 1.5m and 3.0m, with the option to combine poles for longer spans. The design accommodates various wall types, including wood, brick/masonry, and cavity walls, with specific recommendations for each to ensure a secure installation.

Important Technical Specifications:

Available Lengths: 1.5m and 3.0m. The 1.5m kit includes one pole, while the 3.0m kit includes two 1.5m poles and a joiner.
Bracket Quantity:
- 1.5m kit: 2 brackets
- 3.0m kit: 3 brackets
- For heavy-weight curtains, three brackets may be required even for the 1.5m length.
Finials: 2 finials are included in both kits.
Joiner: One joiner is included with the 3.0m kit for connecting the two 1.5m poles.
Maximum Curtain Weights:
- 2 Brackets: 14kg (for 1.5m and 3.0m lengths)
- 3 Brackets: 14kg (for 3.0m length). The document indicates "n/a" for 3 brackets on a 1.5m length, implying this configuration is not standard or tested for this weight.
- These weights are calculated assuming the pole is fitted to a secure wooden batten.
Bracket Spacing:
- For 1.5m poles, brackets are positioned approximately 10cm from each end.
- For 3.0m poles, brackets are positioned approximately 10cm from each end, with a third bracket in the center, supporting the pole joint.
Pole Centre Line: The pole centre line should be approximately 10cm above the window frame.
Bracket Hole Spacing: The wall mounting plate has a hole spacing of 13mm from the pole centre.
Included Fittings per Bracket: 3x Screws, 3x Wall plugs, 1x Allen key.

Usage Features:

Pre-assembly Preparation: Users are advised to read instructions thoroughly and check all pack contents against the provided checklist before assembly.
Tools Required: The manual illustrates common household tools such as a drill, screwdriver, tape measure, pencil, spirit level, and possibly a saw for cutting poles.
Assembly Time: Approximately 30 minutes with 2 people.
Wall Fixing Guidance:
- Wood: Ensure fixing to solid wood, not chipboard, to prevent screws from pulling out.
- Brick or Masonry: Use appropriate wall plugs for sound walls.
- Cavity Wall: Special toggle wall plugs are required; users are advised to seek expert advice.
- Users are encouraged to consult a local builders' merchant or DIY store if unsure about the correct wall fixing.
Measurement and Marking:
- Measure windows to determine pole length.
- Use the wall mounting plate as a template to mark bracket positions.
- Drill holes and fit plugs and screws.
Pole Cutting (if required):
- Mask the area to be cut to avoid damage.
- If using two poles, cut equal lengths from each.
- File sharp edges after cutting to prevent injury or damage to components.
Pole Joining:
- Slide the joining piece into the uncut end of one pole.
- Slide the second pole onto the joining piece, ensuring equal lengths of the joiner are inserted into each pole.
- Pole joints should always be at the halfway point of the total length and supported by a bracket.
Bracket Assembly:
- Push the back plate cover onto the wall mounting plate.
- Screw the fixing barrel onto the plate until tight.
- Slide the bracket onto the fixing barrel, ensuring the base is flush with the cover plate and the bracket faces upwards.
- Tighten the locking screws.
Curtain Installation:
- Slide curtains onto the pole before fitting the pole to the brackets.
- Leave the last eyelet or loop hanging from the end of the pole.
- If using a centre bracket, a curtain will need to be hung from each end of the pole.
Pole Securing:
- Remove the pole retainer, place the pole in the bracket, and re-insert the retainer firmly to grip the pole.
Finial Installation:
- Position one loop or eyelet between the bracket and the finial.
- Push the finial onto the end of the pole.
Testing: Test the installation by drawing the curtains across the pole.

Maintenance Features:

Care: Use a household spray polish to ensure free movement of the curtain along the pole.
Environment: Do not install in high humidity environments, such as bathrooms.
Safety Instructions:
- Step Ladder Use: Only use a step ladder for installation; do not overreach. Always move the step ladder to maintain a safe working position.
- Weight Support: Do not hold or lean on the track to support your weight.
- Two-Person Installation: Recommended for larger tracks.
- Power Tools: Exercise care when using power tools; use of a Residual Current Device (RCD) is recommended.
- Eye Protection: Always use eye protection when drilling.
- Hidden Hazards: Be aware of hidden pipe runs and cables in walls.
- Liability: No liability for damage or injury from incorrectly installed or assembled furniture.
- Child Safety: Keep out of reach of young children; small parts pose a choking hazard.
- Documentation: Keep instructions and batch code for future reference and queries.

The document emphasizes the importance of proper installation for safety and optimal performance, advising professional consultation when in doubt about wall fixing or suitability.