What to do if the Jorvet J1060Q Medical Equipment displays 'Motor Stop'?
If the Jorvet Medical Equipment displays 'Motor Stop', ensure the infusion set is properly installed, allowing the motor to drive the peristaltic pump normally. If the issue persists, contact the manufacturer for maintenance, as the infusion pump may be failing.
What to do if the Jorvet J1060Q displays 'Up Occlusion'?
If the Jorvet Medical Equipment displays 'Up Occlusion', ensure that the infusion inlet is open.
What to do if the Jorvet J1060Q Medical Equipment displays 'Bubble'?
If the Jorvet Medical Equipment displays 'Bubble', properly install the infusion set, ensuring it is mounted to the slot of the bubble detector. If there is air inside the infusion tube, flick the tube or press the Bolus key to purge the bubbles. Check the infusion inlet for blockages. If the bubble sensor is damaged, replace it. If the alarm persists, press the Clear key to cancel it manually.
What to do if the Jorvet Medical Equipment displays 'Empty'?
If the Jorvet Medical Equipment displays 'Empty', check if the infusion bottle or bag is empty. Also, check if Murphy's dropper is misty or too tilted, causing liquid to flow down along the wall instead of dripping.
What to do if the Jorvet J1060Q displays 'Door open'?
If the Jorvet Medical Equipment displays 'Door open', close the pump door and lock it.
What to do if the Jorvet J1060Q Medical Equipment displays 'Drop Sensor Failure'?
If the Jorvet Medical Equipment displays 'Drop Sensor Failure', try reconnecting the sensor. If the connection is damaged, contact the manufacturer for maintenance.
What to do if the Jorvet J1060Q displays 'Abnormal up-pressure'?
If the Jorvet Medical Equipment displays 'Abnormal up-pressure', check for strong electromagnetic interference around the device. If present, remove the source of interference and restart the infusion pump.
What to do if the Jorvet Medical Equipment displays 'Abnormal down pressure'?
If the Jorvet Medical Equipment displays 'Abnormal down pressure', check for strong electromagnetic interference around the device. If present, remove the source of interference and restart the infusion pump. If the issue persists, the pressure sensor may be damaged, in which case you should contact the manufacturer for maintenance.
What to do if the Jorvet Medical Equipment displays 'Pressure Pre-Alarm'?
If the Jorvet Medical Equipment displays 'Pressure Pre-Alarm', check whether the tube is slightly blocked, causing the pressure to rise. You can also set the pressure level to a higher setting.
What to do if the Jorvet Medical Equipment displays 'Battery off'?
If the Jorvet Medical Equipment displays 'Battery off', install the batteries correctly, as the battery connection may be loose.
Provides a welcome message and advises reading the manual before use to avoid injury or risks.
Lists crucial safety precautions for operating the infusion pump, covering usage conditions and potential hazards.
Defines the intended use of the infusion pump in medical institutions for accurate intravenous infusion.
Details IV Set Options/Size and various Infusion Modes (Volume, Drop, Program, Weight, Drug Library, Bolus, KVO).
Details power dissipation, display, power supply, battery, protection, net weight, and dimensions.
Specifies operating temperature, relative humidity, and atmospheric pressure requirements for the pump.
Identifies and labels external parts of the infusion pump like Handle, LCD, Key, Fluid warmer, and Door latch.
Details the components of the infusion tube pathway: guide slots, pressure sensors, and peristaltic pump.
Explains the various status icons and parameters displayed on the infusion pump's LCD screen.
Illustrates the internal components and assembly of the infusion pump, showing boards, housing, and battery.
Lists the items included in the infusion pump package upon unpacking.
Instructions for horizontal installation of the infusion pump on a bracket.
Details vertical installation on a bracket and installation on a cylinder using a stand.
Explains installation on a square tube.
Details the purpose and connection of AC, Drop Sensor, and Network sockets on the rear of the pump.
Explains the function of each key on the infusion pump's front housing for operation.
Illustrates the step-by-step process for operating the infusion pump from installation to start.
Details how to select and configure the Volume Mode for infusion.
Explains how to set VTBI, Rate, and Time parameters in Volume Mode.
Details setting the Rate and Time parameters for infusion.
Explains how to set the infusion using a simple rate mode.
Describes how to program infusion in 8 stages, including setting VTBI and rate.
Explains how to set pause stages within the programmed infusion.
Details how to review and modify programmed infusion stages.
Details how to select and input parameters for Dose/weight mode infusion.
Explains how to import, export, and operate the drug library for infusion.
Details how to input and operate known drug concentrations within the drug library.
Explains how to input dose rate, weight, unit, and VTBI for unknown drug concentrations.
Covers Auto Bolus and Manual Bolus functions for rapid infusion.
Details setting parameters and initiating Auto Bolus infusion.
Explains how to perform and stop Manual Bolus infusion.
Covers IV Set selection, brand management, and size selection.
Instructions on how to stop the infusion process.
Steps for safely powering off the infusion pump.
How to put the infusion pump into standby mode and how to exit it.
Allows modification of VTBI, Rate, and Time during infusion.
Procedure for purging air from the infusion tube.
How to mute alarms and the duration of the mute function.
Steps to clear alarms and understand alarm conditions.
Resets the VI (Volume Infused) parameter.
How to check the remaining battery runtime under the current infusion rate.
Instructions for setting the fluid warmer temperature and range.
Configures pre-alarms for when infusion is nearing completion.
Allows setting up pre-alarms for bottom occlusion detection.
Configures automatic locking of the keypad after a set period of inactivity.
How to manually lock and unlock the keypad.
How to view stored history records directly on the infusion pump.
Procedure for exporting history records to a computer via cable.
Provides a table of alarm messages, possible failures, and corresponding checks and repairs.
Details a table of checkpoints, procedures, and check stages for routine maintenance and inspection.
Lists general specifications including flow rate, accuracy, bolus, VTBI, weight, pressure, and battery runtime.
Provides data on occlusion alarm response times at different pressure thresholds and rates.
Details AC supply voltage, maximum power, and fuse protection.
Specifies battery type, weight, runtime, and charging time.
Information about wired or wireless communication via RS232.
Lists compliance with medical directives and standards like CE, CFDA, EMC, and RoHS.
Details the physical dimensions and weight of the infusion pump.
Specifies environmental conditions for storage and lists forbidden storage environments.
Explains the meaning of various symbols used in the manual and on the device.
Details emission tests and compliance for electromagnetic interference.
Details immunity tests, compliance, and guidance for electromagnetic environments.
Presents graphs and data on infusion pump accuracy and bias over time.
States responsibility for compliance when integrating the pump into a medical system.
General| Brand | Jorvet |
|---|---|
| Model | J1060Q |
| Category | Medical Equipment |
| Language | English |
To Next Page
