JRC JMA-9923-9XA User Manual

lfdl
@
aaaaoof
oaaaaaooaaoaaaaaaoaaoaaooaoof
oao
@
EBL1 starting
point
mode
Sets
whether
the
EBLI starting
point
is
placed
al the center
of the
own
ship
or
at an arbitrary
position
on
the radar screen.
This
has the
same
function
as depressing
the EBLI switch
on
the
conlrol
panel
for a long
period.
tt:
CENTER
Indicates
that
the
EBLI starting
point
is at the own
ship
position.
@:
OFFSET
lndicates that the
EBLI starting
point
is not at the own ship
position.
In this strate, the starting
point
may be
at
the cursor
posiiion
or it may
be
fixed
at
an arbitrary
position
on
the
screen.
When
the
button
is
clicked,
the starting
point
will move
with the
cursor
posilion,
then
when
the left
button
is
clicked
the starting
point
will
be
fixed at the
cursor location.
{:
After
moving
the
L/L
FIX EBLI
starting
point,
the
starting
point
is
fixed by
the
latitude and
longitude
values.
lf the starting
point
moves
out
of
the
screen, then it
will be
reset
automatically so
that
the
starting
pojnl
is
at the own ship
position.
Note:
When the EBL1 starting
point
moves,
the mode O or L is
indicated
by the
position
selected
among the
EBL OFFSET ORIGIN menu.
EBL2 starting
point
mode
Sets
whether the
EBL2
starting
point
is
placed
at
the center
of
the own ship or
at an
arbitrary
position
on
the
radar
screen.
Everything
else is the
same
as that
for the EBL2 starting
point
mode.
Speed
unit setting
Sets
the speed
unit.
Clicking
this
button
will open
a
pull-down
menu, A unit can be selected
from
one
of the
following.
An alarm
is
activated
if the
selected speed unit
is not e,onnected
to
the radar.
Options:
MANUAL, LOG
(1-axis
log),
2AXW
(2-axis
over
water), 2AXG
(2-axis
over
ground),
GPS
lf
the
speed
unit setting
is
"MANUAL,"
then
placing
the cursor
over
the numeric
section and
left
clicking
will
allow numeric
input.
SET/DRIFT
Turns
on and off SET/DRIFT correction.
lf
CORRECTION
is
on for this
setting,
then
"CORR"
will be displayed next to
the
button.
The
number
displayed
next to
'CORR'
at
this
time
will
be valid.
Also, correction can
only
be
set
when
the speed
unit is in the
MANUAL
or LOG
(1-axis
log)
modes.
SET
setting
Placing the cursor over
ihe
numeric
section and
left clicking
will
allow numeric input. This
setting is only valid
if
CORRECTION
is ON.
DRIFT setting
Placing the cursor over the
numeric
section and
left
clicking
will
allow
numeric input. This
setting is only valid if CORRECTION
is
ON.
display mode
the
date mode to be displayed
on
the
screen.
: Turns off the time
display.
; Globallime display
(UCT).
: Localtime
display
(LOCAL).
ARPA,
PAST POSN vector
mode setting
These
set the vector display
mode.
T
True
vector
R:
Relative vector
These
settings
work
concurrently.
(D
Date
Sets
g
til
E
@
@
2-10

JRC JMA-9923-9XA Specifications

General

Brand	JRC
Model	JMA-9923-9XA
Category	Marine Radar
Language	English