Jumbo CBP-247 - User Manual

To Next Page

FORM CBP-1003 / Rev. 1-14

ASSEMBLY and INSTALLATION INSTRUCTIONS:

1) Remove the plastic cap from the Post Base Section with the external

threads (C). Screw the (2) threaded Post Base Sections (B & C)

together – see Figure 1.

2) For added security and theft prevention there are (3) shallow holes

around the outside perimeter of the internally threaded end of the

Part B Post Base Section of the Post Base.

These holes partially expose the threads from the

outside and are intended to allow the threads to

be deformed to prevent disassembly of the base

sections (B & C).

Using a nail set or a pin punch and a hammer, punch

into each of the (3) shallow holes in Post Section B

from two opposite angles to deform the threads

(see Fig. 2). Make sure the threads are thoroughly

deformed so the (2) Post Sections (B & C) cannot

be unscrewed.

3) Use a post hole digger to make a hole a

minimum of 12" dia. x 36" deep. Fill the

hole with concrete – see Figure 3.

Note: Local soil conditions may require

a larger footing. Check local codes.

4) Place one end of the assembled Post Base

into the concrete with the top end 26"

above ground level and plumb it vertically

– see Figure 3. Allow the concrete to cure

before installing the Grill Firebox (A) on

the Post.

5) Install the Grill (A) on the Post by placing

the 2-3/8" dia. Holes in the Swivel

Mechanism of the Grill Firebox over the

end of the Post Base – see Figure 3.

6) To lock the Grill Firebox (A) on the Post Base: Line up the

Holes on the front and back of the Grill Swivel Mechanism

with the Holes at the top of the Post Base. Insert the included

5" Locking Pin (D) through the aligned holes leaving an

equal length of Pin protruding from each side of the Swivel

Mechanism – see Figure 4.

7) Rotate the Grill Firebox (A) (1) complete revolution – see

Figure 4. The Locking Pin (D) will be bent and drawn into

the Swivel Mechanism to lock the Grill onto the Post Base.

The Grill Firebox cannot be removed from the Post Base

when this step is complete.

Grill Maintenance Instructions are on Page 2.

The Model CBP-247 Backyard Charcoal Grill includes:

(1) Grill Firebox -Part A

(1) 21" long Post Base Section with (1) internally threaded end -Part B

(1) 21" long Post Base Section with (1) externally threaded end -Part C

(1) 5" Locking Pin to secure the Grill to the Post Base -Part D

MIN 12'' DIA x 36'' DEEP

CONCRETE FOOTING

RECOMMENDED

26''

15-1/4''

NOTE:

LOCAL CONDITIONS

MAY REQUIRE

LARGER FOOTING.

CHECK LOCAL CODES.

PLUMB POST VERTICALLY

SWIVEL MECHANISM

OF THE GRILL

FIREBOX (A)

FIGURE 3

Park Style

BACKYARD CHARCOAL GRILL

Model CBP-247

Page 1

Need help?

Do you have a question about the Jumbo CBP-247 and is the answer not in the manual?

Summary

Backyard Charcoal Grill Model CBP-247

Assembly and Installation Instructions

Steps to assemble and install the charcoal grill, including post base connection and mounting.

Connect Post Base Sections

Connect the externally and internally threaded post base sections together.

Secure Post Base Threads

Deform post base threads to prevent unauthorized disassembly.

Install Concrete Footing

Dig a hole, pour concrete, and set the post base vertically.

Mount and Lock Grill Firebox

Place the grill firebox onto the post and secure it with the locking pin.

Grill Maintenance

Firebox Cleaning

Regularly clean charcoal and wood ash from the firebox bottom.

High Heat Paint Care

Maintain high heat paint by brushing off rust and reapplying enamel.

Cooking Grate Maintenance

Clean grate with wire brush; use foil if rust persists.