JVC GY-X1TC - Page 11

@ [0° 120° 240°] SC phase switch
Adjusts
the
colour
subcarrier
phase
of
this
unit
in
three
steps
(0°,
120°,
and
240°)
with
respect
to
the
reference
sync
signal
input
to
connector
@
in
genlock
operation.
@® [SC FINE] SC phase control
Fine-adjusts
the
colour
subcarrier
phase
of
this
unit
with
respect
to
the
reference
sync
signal
input
to
connector
@
in
gelock operation.
@ [H] H phase control
Adjusts
the
horizontal
sync
phase
of
this
unit
with
respect
to
the
reference
sync
signal
input
to
connector
@
in
genlock
operation.
@ Time code display
Displays the time code or user's bits.
@® [ADVANCE] Advance button
Used
to
alter
the
data
of
the
digit
selected
with
button
®
@ [SHIFT] Shift button
Used
to
select
the
digit
of
the
time
code
or
user’s
bits
to
be
set.
@ [HOLD] Hold button ;
Press
this
button
before
starting
setting
the
time
code
or
user’s
bits.
@
[PRESET]
Preset
button
When
this
button
is
pressed
after
the
required
time
code
or
user's
bits
have
been
set,
the
time
code
or
user's
bits
are
preset.
@
[REC/FREE]
Time
code
mode
select
switch
REC:
Counts
the
time
code
only
when
the
VTR
is
recording.
:
FREE:
Counts
the
time
code
continuously
regardless
of
the
VTR
status.
(Counting
stops
when
the
power
is
turned
off.)
@® [VITC] VITC on/off switch
ON: Jo record the VITC time code.
OFF: Not to record the VITC time code.
@ [TC/UB] Display select switch
Selects the mode of the time code display@.
TC: ‘To display the time code.
UB: To display the user's bits.
@
[GENLOCK
INPUT]
External
reference
signal
input
connector
Apply
a
composite
video
signal
or
black
burst
for
genlock
operation.
@
[VIDEO
OUTPUT]
Camera
signal
output
connector
Delivers
the
video
signal
of
the
scene
being
shot,
not
the
VTR
playback
signal.
@
[RM]
Remote
control
signal
input
connector
Connect
an
optional
local
remote
control
unit
(RM-LP80).
—10—
Audio
box
SxS
®
[MIC
SELECT]
Microphone
select
switch
Selects
the
microphone
to
be
used
for
recording.
INT:
Built-in
monaural
microphone
EXT:
Microphone
connected
to
connector
®
or
@.
®
[MIC
INPUT]
External
microphone
connector
(6-pin)
When
a
microphone
is
connected
to
this
terminal,
set
switch
@
to
“EXT”.
This
terminal
is
in
parallel
with
terminal
@.
R (Hot)
+9 V DC
GND
L (Hot)
L (Cold)
R (Cold)
@
[MIC
IN
AUD-1/L,
AUD-2/R]
External
microphone
connectors
(XLR
3-pin)
AUD-1/L
for
channel
1
(left
channel),
and
AUD-2/R
for
channel
2
(right
channel).
When
a
microphone
is
connected
to
this
terminal,
set
switch
@
to
“EXT”.
This
terminal
is
in
parallel
with
terminal
®.
[PinNo.[ Function
1 GND
2 HOT
3 COLD
Note
Do not use connectors @ and @ at the same time, otherwise
the correct input level may not be obtained.
@ Earphone jack
Allows monitoring of the following audio signals via an
earphone:
@ Microphone input
e VTR playback audio