To Next PageTo Next Page
Need help?Do you have a question about the K-Edge GARMIN Mount XL and is the answer not in the manual?
Details the K-EDGE GARMIN Mount XL's design and 7mm extension for GARMIN Edge ® 1000.
Lists compatible GARMIN Edge and Forerunner models, noting specific requirements for 910XT.
Provides general safety advice for installation and use, emphasizing potential damage and injury.
Strongly recommends using a tether for GARMIN computers and provides part number.
Lists the K-EDGE GARMIN Mount XL, M4x12mm bolts, and M3x6mm bolts.
Separate the upper and lower clamp halves by removing the 2x M4 x 12 bolts.
Install the mount onto the right (driveside) of the handlebar stem.
Reinstall the upper clamp half back onto the lower clamp half.
Install the 2x M4 x 12mm bolts into the clamp assembly without fully tightening.
Position the mount as desired and lightly tighten the 2x M4 x 12mm bolts.
Carefully torque both 2x M4 x 12mm bolts to 2 N-m using an alternating pattern.
If using Edge 1000 (Landscape) or Forerunner 310XT/910XT, proceed to Insert Adjustment.
Remove the 2x M3 x 6mm Flat Head Screws holding the K13-503 insert.
Reposition the K13-503 insert as shown in the diagram.
Reinstall the 2x M3 x 6mm Flat Head Screws, but do not fully tighten.
Carefully torque the 2x M3 x 6mm Flat Head Screws to a maximum of 1 N-m.
Step-by-step guide for attaching the GARMIN tether to the computer and mount arm.
Steps for safely removing the tether from the GARMIN mount arm.
Addresses computer hitting stem cap; suggests checking mount position.
Addresses Forerunner 910XT hitting mount arm; suggests contacting K-Edge for a spacer.
Addresses play in the mount; suggests checking and increasing torque on M3 screws.
Addresses mount moving downward; suggests checking torque on M4 bolts.
Provides contact details for K-EDGE Support if issues persist after troubleshooting.
The K-EDGE GARMIN Mount XL (K13-505) is a robust and precisely engineered accessory designed to securely hold your Garmin Edge® cycling computer or Forerunner® watch on your bicycle's handlebars. Crafted in the USA, this mount is an essential component for cyclists who rely on their Garmin devices for navigation, performance tracking, and data logging during rides. Its primary function is to provide a stable and easily accessible platform for your Garmin computer, ensuring it remains visible and secure even on challenging terrain.
The design of the K13-505 GARMIN Mount XL is an evolution of the K13-500 GARMIN Mount, featuring a 7mm extension specifically engineered to accommodate the larger GARMIN Edge® 1000 computer in landscape mode. This thoughtful design ensures compatibility with a wide range of Garmin devices, including the Edge® 200, 500, 510, 800, 810, and 1000. Additionally, it supports the GARMIN Forerunner® 310XT when used with a quick-release kit (purchased separately from GARMIN). For users of the GARMIN Forerunner® 910XT, a spacer may be required for proper clearance, and K-EDGE can provide further information on this.
Installation of the K-EDGE GARMIN Mount XL is designed to be straightforward, though careful attention to the provided instructions and proper torque values is crucial for safety and optimal performance. The mount consists of an upper clamp half (K13-502) and a lower clamp half (K13-506), which are secured together with two M4 x 12mm bolts. The mount is intended to be installed on the right side (driveside) of the stem on the handlebar. Users are guided through separating the clamp halves, positioning the mount, and then reassembling and tightening the bolts to a specified torque of 2 N-m using an alternating pattern. This ensures a secure and balanced attachment to the handlebar.
A key usage feature of the K13-505 is its adjustable insert (K13-503), which allows for customization based on the specific Garmin device being used. While the mount is factory assembled for immediate use with most Garmin Edge® computers without any adjustment, users intending to use the GARMIN Edge® 1000 in landscape mode or a Forerunner® 310XT/910XT computer will need to adjust the insert. This adjustment involves removing two M3 x 6mm Flat Head Screws, repositioning the K13-503 insert to the appropriate orientation, and then reinstalling and carefully torquing the screws to a maximum of 1 N-m. It is important not to over-torque these smaller screws, and a small amount of thread lock is applied at the factory, with recommendations for additional application if the bolt is adjusted multiple times.
Safety is a paramount concern, and the K-EDGE GARMIN Mount XL incorporates a critical safety feature: the K13-503 insert is designed to fail before the tabs on the back of the Garmin computer in the event of a crash or abrupt impact. This design helps protect your valuable Garmin device from more significant damage. Furthermore, the use of a tether is strongly recommended for any Garmin computer to prevent loss or damage in such events. Garmin offers a tether (Part #010-11251-16) that can be purchased separately. The instructions detail how to attach the tether to your Garmin computer and then loop it securely around the "neck" of the GARMIN mount arm, ensuring it is synched tightly. This provides an additional layer of security, anchoring your device to a rigid point on the mount.
Maintenance features primarily revolve around ensuring the continued secure attachment of the mount and device. It is strongly recommended that users periodically check all bolts for proper torque. This routine check helps prevent loosening over time due to vibrations or impacts during rides, which could compromise the stability of the mount and the security of the Garmin device. Troubleshooting tips are also provided for common issues, such as the computer hitting the front stem cap (suggesting adjustment of the mount's position), the computer hitting the arm of the K13-505 (indicating a potential need for a spacer for Forerunner® 910XT users), or experiencing play in the computer's attachment (suggesting a slight increase in torque for the M3 x 6mm Flat Head Screws). If the mount itself moves downward, checking the torque of the M4 x 12mm clamp bolts is advised. For any persistent issues, K-EDGE Support is available for assistance, emphasizing the importance of providing full details for effective help.
In summary, the K-EDGE GARMIN Mount XL is a meticulously designed, highly compatible, and user-friendly solution for integrating your Garmin cycling computer or watch with your bicycle. Its robust construction, adjustable features, and emphasis on safety through tether recommendations and protective insert design make it a reliable choice for cyclists seeking a secure and optimal viewing experience for their Garmin devices. Proper installation and routine maintenance are key to maximizing its performance and ensuring the longevity of both the mount and your valuable Garmin equipment.
General| Mounting Style | Handlebar Mount |
|---|---|
| Color | Black |
| Clamp Diameter | 31.8mm |
| Finish | Anodized |
| Compatibility | Garmin Edge series |
| Material | Aluminum |
