2
K-SMART3 Overview
LEDs and Security
Features
The K-SMART3 has 4 distinct
LEDs to report the state of a
system-specific function. In
addition, the K-SMART3 has
an anti-tamper capability
and a heartbeat for en-
hanced reader security. The
following sub-headings re-
view the K-SMART3’s LED,
anti-tamper and heartbeat
functions. Control boards
require System PROM ver-
sion 9.39 or higher when
connected to a K-SMART3
reader for full functionality;
for example, using LED 3 for
Present3 or LED 4 for Global
Lockdown.
LED 1—Door Lock State
• Red—indicates the door is locked / remains red on an Access Denied
• Green—indicates the door is unlocked / green during Relay Unlock Time On and
Access Granted
The control board must be configured for Reader LED (Red/Green Enabled) mode.
LED 2—Power
The backlit Keyscan logo indicates reader power:
• Not illuminated—indicates the reader does not have power
• Illuminated blue—indicates the reader has power
LED 3—Present3
The Present3 mode can trigger a door lock and change time zone schedules. When con-
figured for operation at the reader, LED 3 functions as follows:
• Not illuminated—Present3 is off/Door Toggle - locked/Schedule - time zone is on
• Illuminated amber—Present3 is on/Door Toggle - unlocked/Schedule - time zone is
off
LED 4—Global Lockdown
LED 4 indicates when a Global Lockdown is in effect as follows:
• Not illuminated—a Global Lockdown is not in effect
• Illuminated red—a Global Lockdown is in effect
The reader must be connected to a control board that has Global Lockdown configured.
Note: LED 3—Present3 and LED 4—Global Lockdown are unique features for Keyscan
control boards and require System PROM firmware version 9.39 or higher.
7
K-SMART3 Enhanced Features
K-SMART3 enhanced features, which include Heartbeat and Tamper, are turned on by
default. With the purchase of the K-PC2 programming card, K-SMART3 enhanced features
can be toggled on and off. This will enable backwards compatibility with previous versions
of Keyscan ACUs, even if they do not have the required firmware 9.39 or higher to work
with other manufacturer’s access control systems.
If the K-SMART3 enhanced features are used on an un-supported access control board,
the reader will produce a Card Not in ACU alarm approximately every 60 seconds. This
will not affect the reader’s ability to read cards.
Keep this programming card close at hand for future use with any K-SMART3 reader to
toggle the enhanced features on or off. K-PC2 programming cards are available in pack-
ages of 5 individual cards.
Specifications
Dimensions:
Mullion: 11.5 cm x 4.49 cm x 1.7 cm (4 7/16” x 1 11/16” x 11/16”)
Wall Plate: 12 cm x 7.6 cm x 1.6 cm (4 3/4” x 3” x 5/8”)
Power Requirements
12 VDC, 125mA
Read Range (with typical clamshell card)
Off Metal: up to 3 cm
On Metal: up to 3 cm
Cable
18” wire pigtail standard
Wiegand interface—22 AWG 6 conductor shielded cable, 152 metres/500 ft. maximum
Environmental
Operating Temperature: -40
to 66
°C (-40
to 150.8
°F), 93% RH
Installation
Installation and wiring of systems must be in accordance with the National Electrical
Code, ANSI/NFPA 70.
Connections
Connections must be in accordance with NFPA 70. Reader and/or control unit power
sources must not be connected to a receptacle controlled by a switch.
Certifications
UL-294 - Fifth Edition, CAN/ULC-S319-5 - First Edition, FCC ID: WFW-KSMART3 & IC:
5241A-KSMART3, ETSI EN 301 489-1 V2.1.1 (2017-02), ETSI EN 301 489-3 V2.1.1
(2017-03), ETSI EN 301 489-17 V3.1.1 (2017-02), EN 55032: 2012/AC:2013, ETSI EN
300 330 V2.1.1 (2017-02), ETSI EN 300 328 V2.1.1 (2016-11), Canadian Industrial De-
sign Certificate of Registration: 169,198 and 169,199.
To Next Page
Loading...
