Need help?Do you have a question about the Kandi USA 150GKA-2 Series and is the answer not in the manual?
Warning against operation by individuals under 16 years old.
Improper ATV use can lead to serious injury or death.
Rules for safe operation including speed, passengers, and grip.
Overview of the kart's design and purpose.
Detailed parameters of the off-road kart including dimensions and engine.
Instructions for assembling the kart's components.
Do not drive at excessive speed and maintain a proper gap with other vehicles.
Inspect the kart before driving for safe operation.
Ensure driver is seated and vehicle is controllable before starting the engine.
Drive with defined capacity, never overload, and follow passenger rules.
Keep hands on the steering wheel and ensure directional control.
Practice low-speed turning and avoid excessive speed.
Follow procedures, don't lend, avoid streets, avoid alcohol/drugs.
Drive carefully on slippery/strange roads; qualified training is necessary.
Driver must be over 16 with adequate understanding and judgment.
Add petrol to the oil tank before first use, observe fuel/oil ratios.
Use defined tire types and maintain correct air pressure for braking and turning.
Do not change component positions or add attachments without permission.
Avoid operating in closed spaces and keep away from hot engine parts.
Follow local suggestions and wear helmet/protective clothing.
Fasten seat belt and keep body parts inside the vehicle.
Store away from heat/fire; empty fuel for long-term storage.
Maintenance requires experience and must be done under safe conditions.
Refer to Picture 1.1 for component locations.
Detailed explanation of how to operate key kart components.
Controls the direction of the kart, turning right or left.
Operated by the left foot to slow down or stop the kart.
Operated by the right foot to accelerate or slow down the kart.
Understand gear functions and operating ways to avoid danger.
Overview of ignition key, cutout, headlamp, turn signal, and horn switches.
Controls starting the engine and powering indicators.
Used to stop the engine by pressing the red switch.
Adjust seat position using the lever under the cushion.
Ensure the blowhole is clear and add petrol correctly.
Located between seats, used to brake the kart when stopped.
Add petrol and engine oil to the designated places before starting.
Ensure the gear is in the correct position before running.
Get training, check kart condition, and learn driving rules.
Perform essential checks on the kart before operation.
Add engine oil according to requirements and specified numbers.
Ensure adequate petrol and check for leaks.
Check brake operation and adjust free path if necessary.
Check tire tightness and air pressure for suitability.
Check accelerator movement and return.
Ensure ignition key and blanket switch joints and plugs are tight.
Check screw bolts, nuts, and wheel axles for tightness.
Clear dust and foreign substances from the vehicle underside.
Follow steps to start the engine, including ignition and gas pedal use.
New vehicles require a running-in period of 1000km with careful driving.
Choose a safe place, warm up the engine, and drive gradually.
Control speed when turning and use pedals properly for security.
Loosen pedals and use the hand brake to stop and park the kart safely.
Follow the routine maintenance table, increasing frequency for dusty environments.
Explains symbols (I, C, R, L) for inspection, clean, replace, lubricate.
Warning to cut off the engine before maintenance to avoid damage.
Follow guidance, use correct tools, and seek dealer help if needed.
Procedures for removing, inspecting, and installing spark plugs.
Warning about tightening spark plugs to prevent engine overheating.
Steps for cleaning the air cleaner, including soaking and drying.
Inspect brake pedal free path, system joints, and disk wear.
Measure distance between pedal initial and working positions.
Replace braking disk if less than 3mm thick.
Check accelerator free path and adjust cable if needed.
Check tire pressure and condition, replace if tread depth is less than 2mm.
Connect battery correctly and replace if it cannot store electricity.
Install safety wire/fuse in the box and check for damage.
Adjust idle speed using the adjusting screw bolt.
Perform routine screw inspections and adjust toe-in distance.
General| Brand | Kandi USA |
|---|---|
| Model | 150GKA-2 Series |
| Category | Utility Vehicle |
| Language | English |
To Next Page