Kärcher G 2800 FH - User Manual

Questions and Answers

M
Michele MorrisAug 8, 2025
What to do if my Kärcher Pressure Washer doesn't reach high pressure?
- M
  Meghan BrownAug 8, 2025
  If your Kärcher Pressure Washer isn't reaching high pressure, there could be a few reasons. First, the diameter of your garden hose may be too small; replace it with a 16mm diameter hose or larger. Second, your water supply might be restricted; check the garden hose for kinks, leaks, and blockages. Also, make sure you have enough inlet water supply by turning the water on full force and checking for any obstructions. The water inlet filter could also be clogged, so remove it and rinse it in warm water. Lastly, ensure that the black detergent nozzle is not attached; remove it and attach the high-pressure nozzle.
K
Kelly MorganAug 14, 2025
Why Kärcher High pressure washer unit does not reach high pressure?
- A
  Ariel StricklandAug 14, 2025
  Several factors can prevent your Kärcher high pressure washer from reaching high pressure. The garden hose might be too small; replace it with a 5/8 inch or larger hose. The water supply could be restricted due to kinks, leaks, or blockages in the hose. Ensure you turn the water on full force and check the hose. The water inlet filter might be clogged, in which case you should remove it and rinse it in warm water. Finally, make sure you have removed the black detergent nozzle and attached the high pressure nozzle.
G
Gregory HughesAug 19, 2025
What to do if Kärcher High pressure washer engine will not start?
- K
  Kevin ScottAug 20, 2025
  If your Kärcher high pressure washer engine won't start, there are a few things to check: * Make sure the gas tank is filled with gasoline. * Ensure the choke is in the correct position (slide choke lever out to the closed position). * Release any built-up water pressure in the machine by squeezing the trigger.
A
angela13Aug 26, 2025
How to fix output pressure varies high and low on Kärcher High pressure washer?
- D
  David CareyAug 26, 2025
  If the output pressure of your Kärcher high pressure washer varies, it could be due to several reasons. Ensure there's enough inlet water supply by turning the water on full force and checking for kinks, leaks, or blockages in the garden hose. The pump might be sucking air; check that hoses and fittings are airtight, then turn off the machine and purge the pump by squeezing the trigger gun until a steady flow of water emerges through the nozzle. Also, the water inlet filter could be clogged, so remove it and rinse it in warm water. The spray nozzle might be obstructed; blow out or remove debris with a fine needle. Finally, if the gun, hose, or spray wand is calcified, run distilled vinegar through the detergent suction tube.
R
Robert AdamsSep 1, 2025
How to fix Kärcher Pressure Washer pressure going up and down?
- S
  Shawn BrownSep 1, 2025
  If the output pressure of your Kärcher Pressure Washer varies high and low, consider these potential causes: First, ensure there is enough inlet water supply by turning the water on full force and checking the garden hose for kinks, leaks, or blockages. Next, the pump might be sucking air; check that hoses and fittings are airtight and purge the pump by squeezing the trigger gun until a steady flow of water emerges through the nozzle. Also, the water inlet filter could be clogged; remove the filter and rinse it in warm water. The spray nozzle could also be obstructed; blow out or remove debris with a fine needle. Lastly, the gun, hose, or spray wand might be calcified; run distilled vinegar through the detergent suction tube.