Why is there water or oil leaking from the bottom of my Kärcher HD 3.5/35 G Pressure Washer pump?
The presence of a small amount of water or oil leaking from the bottom of the Kärcher Pressure Washer pump is normal. However, if there is excessive leaking, it is recommended to call a local distributor.
Why is the pressure fluctuating on my Kärcher HD 3.5/35 G Pressure Washer?
If you observe fluctuating pressure in your Kärcher Pressure Washer, the nozzle might be obstructed; try blowing out or removing debris with a fine needle. Another potential cause is the pump sucking air due to a leaking inlet hose. Ensure all hoses and fittings are airtight. Turn off the machine and trigger the spray gun until a steady flow of water emerges through the nozzle. Also, verify that the water supply is sufficient, checking the garden hose for kinks, leaks, or blockages, and ensure the water is turned on full force.
What to do if my Kärcher HD 3.5/35 G engine will not start?
If your Kärcher Pressure Washer engine won't start or stops while operating, first check the oil level and fill the engine with oil if it's low. Also, ensure the fuel tank has gasoline and if there is water in the gasoline, drain the gas tank and fill it with clean fuel.
Why is the pressure low on my Kärcher HD 3.5/35 G Pressure Washer after normal use?
If the pressure of your Kärcher Pressure Washer is low after a period of normal use, the nozzle may be worn. Replacing the nozzle might solve this issue. Also, the unloader valve may be worn, and replacement of the unloader valve may be needed.
Why is my Kärcher HD 3.5/35 G Pressure Washer engine overloaded?
If your Kärcher Pressure Washer engine is overloaded, it might be due to a partially blocked nozzle. Try cleaning the nozzle. Alternatively, excessive pressure from high engine RPM could be the cause. Adjust the engine throttle to lower the RPM.
Why is my Kärcher Pressure Washer pressure fluctuating?
If you observe fluctuating pressure in your Kärcher Pressure Washer, start by checking the nozzle for any obstructions and clear them using a fine needle. Then, verify that all hoses and fittings are airtight. If the pump is sucking air, turn off the machine and trigger the spray gun until a steady flow of water emerges through the nozzle. Also, ensure that the water supply is sufficient by turning the water on full force and checking the garden hose for kinks, leaks, or blockages.
What does it mean if water is leaking from the pump protector of my Kärcher HD 3.5/35 G?
Water leaking from the pump protector of your Kärcher Pressure Washer can occur if the spray gun is closed with the machine running for 5 minutes or longer; open the spray gun or turn off the machine. It may also be due to excessive water supply pressure; place a pressure regulator at the end of the 50' garden hose.
Why is water or oil leaking from the bottom of the pump of my Kärcher HD 3.5/35 G?
A small amount of leaking from the bottom of the pump is normal. If excessive leaking occurs, contact local distributor.
Why does my Kärcher Pressure Washer engine falter?
The engine of your Kärcher Pressure Washer may falter if the choke is opened too soon. To fix this, move the choke to the halfway position until the engine runs smoothly.
What to do if my Kärcher Pressure Washer has no detergent?
If your Kärcher Pressure Washer is not dispensing detergent, first check that the detergent suction tube is properly connected to the machine. If it is, the detergent might be too thick; try diluting it, or use the manufacturer's detergent for best results. Ensure the detergent filter valve is not at the lowest setting; set it to a higher setting. Also, check if the filter on the detergent suction tube is clogged; run warm water through it to remove any debris. If the detergent suction tube is damaged or clogged, remove the obstruction or replace the tube. Finally, if a high-pressure nozzle is attached, replace it with a black detergent nozzle. Check if the discharge nozzle is obstructed, and if so, blow out or remove debris with a fine needle.
General| Power | 3.5 kW |
|---|---|
| Flow Rate | 350 l/h |
| Max. inlet water temperature | 60 °C |
| Power consumption | 3500 W |
| Engine | Electric |
To Next Page
