Kärcher K1700 - User Manual

Questions and Answers

A
aperezAug 14, 2025
Why won't my Kärcher Pressure Washer motor start?
- D
  David JenkinsAug 14, 2025
  There are several reasons why your Kärcher Pressure Washer motor might not start: * The power cord may not be plugged in, so ensure it is properly connected. * The electrical outlet might not be providing enough power; try a different outlet. * The GFCI plug may have tripped; press the 'Reset' button on the GFCI plug. * The circuit breaker may have tripped; reset the circuit breaker. * The thermal overload may be open; switch off the pressure washer and wait for the unit to cool down and reset automatically. * The On/Off pedal may be in the 'OFF' position; turn the pedal to the 'ON' position.
C
Christopher LewisAug 17, 2025
How to fix Kärcher Pressure Washer not reaching high pressure?
- S
  Sarah MayerAug 18, 2025
  If your Kärcher Pressure Washer isn't reaching high pressure, consider these potential causes: * A garden hose with too small of a diameter is being used. Replace it with a 5/8 inch (16mm) or larger garden hose. * The water supply is restricted. Check the garden hose for kinks, leaks, or blockages. * There is not enough inlet water supply. Open the water source fully. * The water inlet filter is clogged. Remove the garden hose adapter and rinse the filter in warm water.
G
gbarberAug 21, 2025
What to do if the output pressure varies on Kärcher Pressure Washer?
- M
  Michael CruzAug 21, 2025
  If the output pressure on your Kärcher Pressure Washer is fluctuating, here are a few things to check: * Ensure there's enough inlet water supply by fully opening the water source and checking the garden hose for kinks, leaks, or blockages. * The pump may be sucking in air. Check that hoses and fittings are airtight. Turn off the machine and purge the pump by squeezing the trigger gun until a steady flow of water emerges through the nozzle. * The water inlet filter could be clogged. Remove the garden hose adapter and rinse it in warm water. * The spray nozzle might be obstructed. Blow out or remove any debris with a fine needle. * The gun, hose, or spray wand may be calcified. Run distilled vinegar through the soap tank.
R
Richard WhiteAug 26, 2025
Why is my Kärcher Pressure Washer not dispensing detergent?
- E
  Eric GoodwinAug 26, 2025
  If your Kärcher Pressure Washer is not dispensing detergent, consider the following: * The detergent might be too thick. Dilute it, and for best results, use Kärcher detergent. * A high-pressure nozzle may be attached. Ensure the soap nozzle is properly installed. * The spray nozzle may be obstructed. Clear any debris with a fine needle.
A
Anthony NelsonAug 28, 2025
How to reduce noise from Kärcher Pressure Washer pump?
- W
  whitemichelleAug 29, 2025
  If your Kärcher Pressure Washer pump is noisy, it might be sucking in air. Check that all hoses and fittings are airtight. Turn off the machine and purge the pump by squeezing the trigger gun until a steady flow of water emerges through the nozzle.
K
Kimberly RoseSep 1, 2025
How to stop Kärcher Pressure Washer garden hose connection from leaking?
- V
  Vincent LloydSep 1, 2025
  If your garden hose connection is leaking, check for loose fittings and tighten them. Also, inspect the rubber washer; if it's missing or worn, insert a new one.
A
Alicia WilsonSep 5, 2025
What causes a Kärcher Pressure Washer spray wand to leak?
- K
  Kimberly MurphySep 5, 2025
  A Kärcher Pressure Washer spray wand can leak if it is not properly attached. Ensure the spray wand is fully inserted into the trigger gun, pressing against the spring tension and twisting it into the locked position.
D
dcobbSep 9, 2025
Why is my Kärcher Pressure Washer pump leaking water?
- D
  Dana MendezSep 9, 2025
  If your Kärcher Pressure Washer pump is leaking water (up to 10 drops per minute is permissible), ensure that all fittings are tightened. Loose fittings can cause leaks.