Kärcher NT 48/1 Instructions

English 9
General
● On completion of wet vacuum cleaning: Clean the
float and container with a damp cloth and dry.
Clip connection
The suction hose is equipped with the clip 2.0 connec-
tion. All accessory parts with nominal width DN 35 and
a clip 2.0 connection can be connected.
Illustration F
Operation
Switching on the device
1. Connect the mains plug.
2. Switch on the device at the main switch.
Cleaning mode
1. Perform cleaning.
Draining the dirt receptacle
● The suction duct is equipped with a float.
● When the maximum permissible waste water level
in the container is reached, the suction volume is in-
terrupted.
1. Switch off the device at the main switch.
2. Drain the waste water via the drain hose.
Illustration G
Switching off the device
1. Switch off the device at the main switch.
2. Pull out the mains plug.
Each time after use
1. Empty the dirt receptacle.
2. Vacuum off the inside and outside of the device and
clean with a moist cloth.
Storing the device
1. Store the suction pipe, suction hose and mains ca-
ble as shown in the illustration.
Illustration H
2. Store the device in a dry room and secure it against
unauthorised use.
Transport
몇 CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
1. Transport the unit as shown in the illustration.
Illustration I
2. When transporting the device in vehicles, secure it
to prevent it from slipping or overturning in accord-
ance with the respective valid guidelines.
Storage
몇 CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
The device may only be operated indoors.
Care and service
 DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the mains plug.
Changing the cartridge filter
1. Unlock and remove the suction head.
2. Turn the suction head by 180 ° and set it down.
3. Unscrew the securing nut.
4. Remove the cartridge filter.
5. Install new cartridge filter.
6. Insert and tighten the securing nut.
7. Fit and lock the suction head.
Troubleshooting guide
 DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the mains plug.
Suction turbine does not start up
1. Check the socket and the power supply fuse.
2. Check the mains cable and the mains plug of the de-
vice.
3. Switch on the device.
Suction turbine runs, but the device does not suck
Float closes suction duct
1. Empty the dirt receptacle.
Suction power decreases
1. Remove any blockages from the suction nozzle,
suction pipe, suction hose or cartridge filter.
2. Change the filled paper filter bag.
3. Change the cartridge filter.
4. Check the drain hose for leaks.
Escaping dust when vacuuming
1. Check that the cartridge filter is correctly fitted.
2. Change the cartridge filter.
Customer Service department
If the malfunction cannot be corrected, the device must
be checked by the Customer Service department.
Warranty
The warranty conditions issued by our sales company
responsible apply in all countries. We shall remedy pos-
sible malfunctions on your device within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
Accessories and spare parts
Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and
safely.
Information on accessories and spare parts can be
found at www.kaercher.com.

Kärcher NT 48/1 Specifications

General

Standard nominal width	35 mm
Dust capacity	48 L
Container material	Plastic
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Maximum input power	1380 W
Airflow	67 l/s
Noise level	72 dB

Weight and Dimensions

Depth	390 mm
Width	490 mm
Height	780 mm
Weight	10500 g