Kenmore 110.2513*410 User Manual (English)

Other manuals for Kenmore 110.2513*410

Questions and Answers:

R
rbeckAug 19, 2025
Why my Kenmore Washer won't start?
- A
  Angela MaloneAug 19, 2025
  If your Kenmore Washer won't run or fill, stops working, or the wash light stays on, here are a few things to check: First, make sure the power cord is plugged into a grounded, 3-prong outlet and that you're not using an extension cord. Check the circuit breaker or fuses. Remember that the lid must be closed for the washer to operate. If the washer is packed too tightly, remove some items and rearrange the load evenly. Also, ensure you are using HE detergent and the correct amount. If suds are the problem, cancel the cycle and run a Rinse & Spin cycle without adding more detergent.
J
Juan KirkAug 21, 2025
What to do if Kenmore 110.2513*410 Washer not draining?
- S
  Stephanie SalinasAug 21, 2025
  If your Kenmore Washer isn't draining or spinning properly, and your loads are still wet, consider these potential causes and solutions: * Small items might be caught in the pump or between the basket and tub. Make sure to empty pockets and use garment bags for small items. * The selected cycle might have a low spin speed. Use a higher spin speed or select the Drain/Spin cycle to remove extra water. * The washer could be tightly packed or unbalanced. Evenly arrange the wet load and select the Drain & Spin cycle. * The drain hose installation might be incorrect. Check the drain hose to ensure it's properly installed and not clogged. The drain hose should not extend more than 4.5" into the standpipe, and the end should not be higher than 96" above the floor.
X
xkentAug 25, 2025
Why is my Kenmore 110.2513*410 Washer load not rinsed?
- D
  David HollandAug 25, 2025
  If your Kenmore Washer load is not being rinsed properly, check the following: Ensure that the hot and cold inlet hoses are not reversed and that both hoses are attached with water flowing to the inlet valve. Both hot and cold water faucets must be turned on. Check for clogged inlet valve screens on the washer and remove any kinks in the inlet hose.
A
Alexis ReynoldsAug 26, 2025
Why is lid locked light flashing on my Kenmore Washer?
- C
  charlotte99Aug 27, 2025
  If the lid locked light is flashing on your Kenmore Washer, make sure the lid is fully closed, as the washer won't start or fill with the lid open. If a cycle was stopped or paused, the lid will remain locked until the basket has completely stopped spinning, which may take several minutes for large or heavy loads.
B
Brian SalazarAug 30, 2025
How to prevent load tangling in Kenmore 110.2513*410 Washer?
- A
  antonio17Aug 30, 2025
  If your laundry is tangling in your Kenmore Washer, ensure the washer is loaded as recommended. Select a cycle with a slower wash action and spin speed, keeping in mind that items will be wetter. Load items in loose heaps evenly around the washplate. Reduce tangling by mixing types of load items and using the recommended cycle for the items being washed.
R
Ronald WashingtonSep 2, 2025
How to remove pet hair from Kenmore 110.2513*410?
- J
  john20Sep 2, 2025
  If you find sand, pet hair, or lint on your load after washing in your Kenmore Washer, it may be necessary to add a Two Rinses to the selected cycle, especially if there is heavy sand, pet hair, lint, or detergent/bleach residue.
T
tgutierrezSep 4, 2025
How to prevent fabric damage in Kenmore 110.2513*410?
- P
  pamelanavarroSep 4, 2025
  To prevent fabric damage in your Kenmore Washer, take these precautions: * Empty pockets of sharp items, zip zippers, and fasten hooks before washing. * Tie all strings and straps to prevent tangling. * Mend any rips or broken threads before washing. * Avoid tightly packing the washer; load items loosely and evenly. * Use the appropriate cycle for the fabrics being washed and add only 1 or 2 items after the washer has started. * Do not pour liquid chlorine bleach directly onto the load, and wipe up any spills. Use the recommended amount of bleach and avoid placing items on top of the bleach dispenser. * Always follow garment care label instructions.
R
Robert EsparzaSep 6, 2025
What to do if too much detergent in Kenmore 110.2513*410 Washer?
- R
  Ryan PowersSep 7, 2025
  If excessive suds are causing your Kenmore Washer to drain and spin slowly or not at all, make sure you are only using HE detergent. Always measure the detergent and follow the directions for your load size. To remove the extra suds, select Rinse & Spin without adding any detergent.
K
Kaitlyn FritzSep 9, 2025
How to get rid of odors in Kenmore Washer?
- W
  wallacejacobSep 9, 2025
  To address odors in your Kenmore Washer: * Run the Clean Washer with bleach cycle monthly. * Unload the washer as soon as the cycle is complete. * Use only HE detergent and measure it correctly, following the manufacturer’s directions.
K
Kristin DiazSep 12, 2025
Why is my Kenmore Washer using the wrong water temperature?
- E
  Eric BaileySep 12, 2025
  If you're experiencing incorrect wash or rinse temperatures with your Kenmore Washer, start by checking that the hot and cold inlet hoses are not reversed. Ensure both hoses are connected to both the washer and the faucet, and that hot and cold water are flowing to the inlet valve. Also, check that the inlet valve screens are not clogged and remove any kinks in the hoses.

Kenmore 110.2513*410 Specifications

General

Brand	Kenmore
Model Number	110.2513*410
Product Type	Washer
Capacity	3.5 cu. ft.
Agitator Type	Dual Action Agitator
Voltage	120V
Color	White
Width	27.5 inches
Depth	27 inches
Height	43 inches
Spin Speed	700 RPM
Water Temperature Settings	5
Cycle Options	Delicates, Drain & Spin, Heavy Duty, Normal, Quick Wash, Rinse & Spin