To Next PageTo Next Page
Need help?Do you have a question about the Kenwood KRC-335 and is the answer not in the manual?
FM Section| FM frequency range | 87.9MHz-107.9MHz |
|---|---|
| FM frequency step | 200kHz |
| FM usable sensitivity | 9.3dBf (0.8µV/75Ω) |
| FM quieting sensitivity | 15.2dBf (1.6µV/75Ω) |
| FM frequency response | 30Hz-15kHz |
| FM signal-to-noise ratio | 70dB (MONO) |
| FM selectivity | 80dB (±400kHz) |
| FM stereo separation | 40dB (1kHz) |
AM Section| AM frequency range | 530kHz-1700kHz |
|---|---|
| AM frequency step | 10kHz |
| AM channel space selection | 9k/10kHz |
| AM usable sensitivity | 28dB µ (25µV) |
Cassette Section| Tape speed | 4.76cm/sec |
|---|---|
| Wow and flutter | 0.08% (WRMS) |
| Cassette frequency response | 30-18kHz (70µs) |
| Cassette separation | 43dB (1kHz) |
| Cassette S/N with Dolby NR off | 57dB |
| Cassette S/N with Dolby BNR on | 65dB |
Amplifier Section| Preout level/load | 1800mV/10kΩ |
|---|---|
| Preout impedance | 600Ω |
| Maximum power | 45W×4 |
| Full bandwidth power | 22W×4 (at less than 1%THD) |
Tone Section| Bass | 100Hz±10dB |
|---|---|
| Middle | 1kHz±10dB |
| Treble | 10kHz±10dB |
General| Operating voltage | 14.4V (11V-16V allowable) |
|---|---|
| Current consumption | 10A |
| Installation size width | 182mm (7-3/16in) |
| Installation size height | 53mm (2-1/16in) |
| Installation size depth | 152mm (6in) |
| Weight | 1.3kg (2.9lbs) |
FM Section| FM frequency range | 87.5MHz-108.0MHz |
|---|---|
| FM frequency step | 50kHz |
| FM usable sensitivity | 9.3dBf (0.8µV/75Ω) |
| FM quieting sensitivity | 15.2dBf (1.6µV/75Ω) |
| FM frequency response | 30Hz-15kHz |
| FM signal-to-noise ratio | 70dB (MONO) |
| FM selectivity | 80dB (±400kHz) |
| FM stereo separation | 40dB (1kHz) |
AM Section| AM frequency range | 531kHz-1611kHz |
|---|---|
| AM frequency step | 9kHz |
| AM channel space selection | 9k/10kHz |
| AM usable sensitivity | 28dB µ (25µV) |
Cassette Section| Tape speed | 4.76cm/sec |
|---|---|
| Wow and flutter | 0.08% (WRMS) |
| Cassette frequency response | 30-14kHz (120µs) |
| Cassette separation | 43dB (1kHz) |
| Cassette S/N with Dolby NR off | 57dB |
| Cassette S/N with Dolby BNR on | 65dB |
Amplifier Section| Preout level/load | 1800mV/10kΩ |
|---|---|
| Preout impedance | 600Ω |
| Maximum power | 45W×4 |
| Full bandwidth power | 22W×4 (at less than 1%THD) |
Tone Section| Bass | 100Hz±10dB |
|---|---|
| Middle | 1kHz±10dB |
| Treble | 10kHz±10dB |
General| Operating voltage | 14.4V (11V-16V allowable) |
|---|---|
| Current consumption | 10A |
| Installation size width | 182mm (7-3/16in) |
| Installation size height | 53mm (2-1/16in) |
| Installation size depth | 152mm (6in) |
| Weight | 1.3kg (2.9lbs) |
Precautions to prevent injury or fire during unit installation and operation.
Steps to prevent short circuits and disconnect the battery before installation.
Connecting input/output wires, speaker wires, and wiring harness.
Installing the unit in the car, reconnecting battery, and pressing reset.
Solutions for common issues like power, buttons, source switching, and memory.
Troubleshooting poor radio reception and antenna problems.
Solutions for tape removal, playback, and blank skip issues.
Solutions for disc playback errors, disc changer connection, and CD-R/RW issues.
Explains system error codes and their meanings for system conditions.
