Kenwood SRC-590 - User Manual

“
STEREO SYSTEM RACK
SRC-590 ©
ASSEMBLY INSTRUCTIONS
KENWOOD
KENWOOD CORPORATION
@PRINTED IN U.S.A B61-0308-00(K)(TCA)
RO171
IMPORTANT: —- = - Notes on Assembling
¢ Before operating your new KENWOOD product, read through this assem- ¢ During assembling, be sure to verify the numbers stamped on the boards.
bly manual carefully to get the most out of it. © Mount the rear panel after assembling the side panel on the bottom shelf
° Save this assembly instructions. 7 at a right angle.
e When mounting the top shelf and kick plate on the side panel, use glue
Before Assembling for adhesive. Be sure to remove any excess glue before it dries.
© {f the amplifier wobbles when its key switches are pressed, insert a woo-
* Be sure to check that all parts are accounted for before disposing of the den dowel into the hole on the side panel and fix the rear of the amplifier.
packing case.
¢ A Phillips screwdriver and a mallet are required for assembling.
Handling Precautions
* Be carefull not to damage the floor and rack. g
® Tempered glass is used for the glass doors for providing sufficient strength.
However, pay attention not to apply excessive force or to scratch the doors.
Cracking or breaking of the glass may occur.
® When moving the cabinet, remove all the components from the rack be-
fore carrying the cabinet. Also do not grasp the top shelf when carrying.
© To allow head radiation from the components, leave a space of 4 inches
between the cabinet and wall.
© Do not place the cabinet in a location subject to direct sunlight or near a
heater, an air-conditioner, or a place with high humidity.
IMPPRTANT SAFEGUARDS _ -- re
A\Caution : Read this page carefully to keep your safety. : :
Please read all of the safety and operating instructions before operating this ~ 4. Impact — Avoid placing the unit on an unstable surface. Install it on a
unit. For best results, follow all warnings placed on the unit and adhere to the horizontal surface not subject to excessive dirt or vibrations.
operating and use instructions. These safety and operating instructions should
be retained for future reference.
Ag
Avy
ered
1. Suffocation — After taking the unit out of the polyethylene bag, be sure
to dispose of the polyethylene bag out of the reach of children. Otherwise,
they may play with the bag, which could cause hazard of suffocation.
5. Modification — Do not attempt to open or modify the unit, for this could
cause fire hazard or malfunction.
2. Water and moisture — Do not place a liquid container, such as a vase and
water basin, on the unit. Also avoid installing the unit in a place subject
to dampness.
6. Cleaning — Do not use thinner, benzine or alcohol. When cleaning the unit,
wipe with a soft, dry cloth.
3. Heat — Do not install the unit near a source of heat, such as a heater, or
under direct sunlight.
7. Abnormal smell — In the event the unit generates smoke or abnormal smell,
immediately switch the power OFF and unplug the power cord. After this,
please contact your dealer or nearest service station as soon as possible.
POWER OFF!

Summary

Important Safeguards

Suffocation Hazard Warning

Warning about plastic bags and suffocation hazard for children.

Water and Moisture Precautions

Avoid placing liquid containers or installing unit in damp places.

Heat and Sunlight Avoidance

Do not install near heat sources or direct sunlight.

Surface Stability Requirement

Install unit on a stable, horizontal surface, avoid dirt/vibrations.

Modification Prohibition

Do not open or modify the unit to prevent fire or malfunction.

Cleaning Instructions

Clean unit with a soft, dry cloth; avoid thinner, benzine, or alcohol.

Abnormal Smell Response

Switch off power and unplug if unit emits smoke or abnormal smell; contact dealer.

Stereo System Rack Assembly

Step 1: Initial Component Setup

Begin assembly process with Step 1, connecting initial parts.

Step 3: Panel and Board Assembly

Assemble side panels with bottom and top boards using screws and dowels.

Step 4: Shelf and Dowel Insertion

Attach shelves to side panels using wood dowels and glue, ensuring correct orientation.

Step 5: Back Panel Installation

Install the back panel using screws, ensuring correct alignment.

Step 6: Hardware and Shelf Pins

Install shelf pins and other small components using screws.

Step 7: Door and Catch Plate Mounting

Mount the glass door and associated catch plates and pads.

Kenwood SRC-590 Specifications