Kettler Scarpia FS 1.0 LTD Gold User Manual (English)

Other manuals for Kettler Scarpia FS 1.0 LTD Gold

Translation Of Original Operating Instructions292 pages

Questions and Answers:

S
Stephanie MeyerAug 18, 2025
How to fix Kettler Bicycle drive system that does not start?
- N
  Nathaniel RobersonAug 18, 2025
  If the drive system or on-board computer of your Kettler Bicycle doesn't start, first ensure the battery is switched on. If the battery level indicator LEDs don't light up, contact your dealer. If the LEDs light up but the system remains off, remove the battery, then re-insert it and try starting the drive system again. If it still fails, remove the battery and clean all contacts with a soft cloth before reinserting and restarting. If problems persist, fully charge the battery before reinserting and restarting. As a last resort, try pressing the On-Off button on the control panel for at least 8 seconds, or if it doesn't start after about 6 seconds, press the On-Off button for at least 2 seconds. If none of these steps work, contact your dealer.
A
Angela MorrisAug 20, 2025
What to do if Kettler Bicycle shows an error message?
- A
  Alex VargasAug 20, 2025
  If you see an error message on your Kettler Bicycle, first, make a note of the system message. Then, shut off and restart the drive system. If the message persists, remove the battery, re-insert it, and restart the system again. If the error message continues to appear, you should contact your specialist dealer for further assistance.
K
Kelly SnyderAug 23, 2025
Why is the assistance not available on my Kettler Bicycle?
- M
  Miranda NealAug 23, 2025
  There are several reasons why the assistance function on your Kettler Bicycle might not be working: * Check if the battery is sufficiently charged and recharge if necessary. * Ensure the system is switched on by pressing the On-Off button on the battery. * Verify that the assistance level is not set to [OFF]. * Make sure you are pushing the pedals, as the pedelec is not a motorbike. * Check the on-board computer indicators if the speed is too high. * If the lock function is activated, use the appropriate on-board computer to deactivate it. * If the battery overheats during rides, switch off the drive system and allow the pedelec to cool down before restarting.
A
Andrew MillerAug 26, 2025
Why does Kettler Bicycle battery drain so fast?
- R
  Robert GouldAug 26, 2025
  If the battery on your Kettler Bicycle discharges quickly, it might be nearing the end of its useful life. In this case, consider replacing the old battery with a new one.
W
wcookAug 27, 2025
What to do if Kettler Bicycle battery cannot be recharged?
- R
  Ralph JohnsonAug 28, 2025
  If your Kettler Bicycle battery won't recharge, check these things: 1. Ensure the charger's mains plug is firmly connected to the socket. Disconnect and reconnect it to be sure, then start charging. 2. Verify the charger plug is securely connected to the battery. Disconnect and reconnect it, then start charging. 3. Confirm the adapter is firmly connected to both the charger plug and the battery's charging port. Reconnect it securely, then start charging. 4. Inspect the connection terminals for any dirt. If dirty, wipe them with a dry cloth before starting to charge.
K
Kimberly MillerAug 30, 2025
Why Kettler Bicycle battery does not start charging?
- J
  Juan RichardsonAug 30, 2025
  If the battery on your Kettler Bicycle does not start charging when you connect the charger, it may be at the end of its useful life. Consider replacing it with a new one.
E
Emily GouldSep 1, 2025
Why do Kettler Bicycle battery and charger become hot?
- E
  Eric PetersonSep 1, 2025
  If the battery and charger of your Kettler Bicycle become hot, it could be due to the temperature exceeding the operating range. Stop the charging process and allow both the battery and charger to cool down. Then, try charging again. If the battery is too hot to touch, it might indicate a problem, and you should contact your dealer.
K
Kevin WalkerSep 3, 2025
Why is the LED on my Kettler Bicycle charger not lighting up?
- A
  Amy MurraySep 3, 2025
  If the LED on the charger of your Kettler Bicycle doesn't light up, it could mean one of several things. First, it's possible that the battery is already fully charged, which is normal. If not, check the charger plug connection to the battery for any contaminants and ensure it's properly inserted. If the LED still doesn't light up, disconnect and reconnect the charger's mains plug, then try charging again.
R
Regina HarringtonSep 6, 2025
What to do if Kettler Bicycle on-board computer shows no data?
- S
  Shawn WrightSep 6, 2025
  If no data is shown on the on-board computer of your Kettler Bicycle when you press the on-off button on the battery, it could be due to several reasons. First, check if the battery charge level is sufficient and charge it if necessary. Also, ensure that the power is switched on by pressing the On-Off button on the battery. If the battery is being charged while fitted to the pedelec, it cannot be switched on, so interrupt charging. Check that the connector is correctly fitted to the power cable. If none of these steps work, there may be a component connected that the system doesn't recognize.
J
Judith WhiteSep 8, 2025
Why is the gear level not showing on my Kettler Bicycle computer?
- C
  Christopher WilliamsSep 8, 2025
  The gear level is only displayed on the on-board computer of your Kettler Bicycle if you are using the electronic gear shift. Ensure that the power cable connector is properly connected. If it is and the gear level is still not showing, contact your specialist dealer.