Ref: KT037218 / KT037225 / KT037232 / KT037249
• A wooden alarm clock
• A USB cable
• A user manual
Safety instructions
Read the safety instructions carefully and use this article only as described in this manual to avoid any risk of damage or injury.
To be used only indoors, and do not put in the sun, or in a humid and hot place.
Operation with a mains unit:
• Never immerse the alarm clock in water or other liquids as this may cause an electric shock.
• Do not use the alarm clock outdoors or in rooms with high ambient humidity, and do not touch the mains unit with wet hands.
• Connect the alarm clock only to an outlet installed in accordance with the regulations and whose voltage corresponds to the technical
characteristics of the mains unit.
The socket outlet used should be easily accessible so that you can quickly unplug the mains unit if necessary.
Do not use the alarm clock if the device, the mains unit or the power cord show signs of damage or if the device has been dropped.
• Avoid strong blows and falls.
• Do not attempt to disassemble or reassemble your product.
• Do not use any cleaning products containing alcohol, ammonia, benzene or abrasive substances. If cleaning is necessary, use a soft cloth.
• Change the batteries when the screen display is abnormal.
• Do not mix new batteries with old ones.
• If a battery has leaked, avoid contact with skin, eyes and mucous membranes. If necessary, rinse the affected areas immediately and
consult a doctor without delay.
• If the alarm clock is not being used, remove the batteries to avoid leakage which could damage the device.
• This product is not a toy. If swallowed, batteries can cause fatal poisoning. Therefore, keep your alarm clock, packaging and batteries out of
the reach of children. If you suspect that your child may have swallowed a battery, seek medical advice immediately.
WOODEN CUBE ALARM CLOCK
2022/07V02/MKG
PACKAGING CONTENT
WARNING & SAFETY INSTRUCTIONS
PRODUCT USE
SRDi - 85430 La Boissière des Landes FRANCE
Warranty
Products are guarranteed against any failure from manufacturing defects.
This warranty does not cover normal wear or tear, or damage caused by improper use, keep your invoice stapled to the user manual.
Directive 2012 / 19 / EU
Correct disposal of this produt
Electronic waste should not be thrown away with household waste. Please recycle them to your authorized agency and check the recycling advice with
the relevant local authorities.
Switching on the product
Open the cover on the back of the alarm clock and insert 3 AAA LR03 batteries, respecting the polarities. Close the cover. The alarm clock turns
on automatically.
You can also plug in your alarm clock using the included cable, connecting it to a suitable USB-A mains charger.
To save money and energy in the long run and reduce the impact on the environment, we recommend the use of rechargeable batteries.
Also, to limit the use of batteries, we advise you to connect your alarm clock to a wall socket, using a compatible mains adapter (not included).
Selection of display mode
By default, the mode is DP-1.
DP-1: The time, date and temperature are displayed automatically in turn.
DP-2: Only the time is displayed.
Press the SET button on the back of the alarm clock to toggle between modes.
Energy saving mode
Press DOWN:
ON:SD : means that the energy saving mode is activated
--:SD : means that the LED lighting is constant
In power saving mode, the LED display will turn off if there is no operation for 20 seconds.
Clap your hands, on the table or on the alarm clock to activate the LED display.
Temperature setting
The temperature is automatically detected after switching on.
Press UP to toggle between degrees Celsius (° C) and degrees Fahrenheit (° F).
Selecting the setting mode
Press and hold the SET button for 3 seconds to enter the setting mode.
You can set the following parameters: Year (from 2000 to 2099), month, date, hour, minute, 12h/24h, AL (alarm): ALA1-ALA2-ALA3, -:E.
«- - : E» means weekday mode.
«ON : E» means that the weekday mode is activated: the alarm sounds from Monday to Friday, and does not sound on weekends.
«- - : E» means that the weekday mode is deactivated: the alarm sounds every day from Monday to Sunday.
When the «Year» symbol is flashing, you can adjust the setting with UP and DOWN.
Then press SET to set the other settings, and change them with UP and DOWN.
When the alarm is activated, you will see a bright dot between the two numbers on the left. This dot will disappear when the alarm is turned
off.
Adjusting the display illumination
Press and hold the UP button for 3 seconds to enter the setting item.
Press the DOWN button to decrease the lighting.
Press UP to increase the lighting.
There are 3 levels of illumination, from L0 (lowest) to L3 (highest).
RESET button
Press the RESET button to restore factory settings.
To Previous Page
Loading...