Khyam HAREWOOD - User Manual

KHYAM QUICK ERECT TENTS
TENTES A MONTAGE RAPIDE
KHYAM
ASSEMBLY INSTRUCTIONS & USER HINTS
NOTICE DE MONTAGE & CONSEILS D’UTILISATION
THE RIDGI-DOME TOURER 400PLUS,
CHATSWORTH, HAREWOOD, HATFIELD &
BALMORAL.
Please read these instructions fully, download or view online the customer service
video @ http://www.khyam.co.uk/info.asp?s=support
prior to using your Ridgidome
for the first time. Please check your tent fully before embarking on your first camping
holiday.
Lisez attentivement ces instructions, téléchargez ou visionnez la vidéo à l’adresse :
http://www.khyam.co.uk/info.asp?s=support avant de monter votre Ridgi-dome pour
la première fois.
WARNING: AVERTISSEMENT :
If this tent is not erected in accordance with the instructions damage could be caused to the joints,
poles or fabric. It is important that the tent is properly guyed at all times, particularly in strong
winds – otherwise pole or joint damage may occur.
Les mâts, les articulations ou les tissus de votre tente peuvent être endommagés si vous ne la
montez pas conformément à ces instructions. Il est très important que la tente soit piquetée et
haubanée correctement si le vent est fort, pour éviter d’endommager les mâts ou les articulations.
DO NOT PUSH TENT PEGS IN BY HAND, ALL TENT PEGS SHOULD BE DRIVEN
HOME USING A WOODEN OR RUBBER FACED MALLET OR SIMILAR TOOL.
N’ENFONCEZ PAS LES PIQUETS A LA MAIN, TOUS LES PIQUETS DOIVENT
ÊTRE MIS EN PLACE EN UTILISANT UN MAILLET BOIS OU CAOUTCHOUC,
OU UN OUTIL SIMILAIRE.
New ‘On Line’ guarantee registration service, simply go to
www.khyam.co.uk/guarantee
for UK sales only to register your Khyam tent guarantee.

Summary

General Information and Warnings

Erection Safety Warnings

Warns about potential damage to joints, poles, or fabric if not erected correctly or guyed properly.

Proper Pegging Technique

Advises using a mallet or similar tool for tent pegs, not hands, to prevent damage.

Khyam Guarantee and Warranty

Product Guarantee Terms

Details the 12-month guarantee for material and workmanship defects, offering repair or replacement.

Warranty Limitations

Excludes faults caused by abuse, misuse, negligence, or damage from extreme weather conditions.

Main Structure Erection

Step 7: Lifting Central Hub

Lifts the central hub to waist height, ensuring fabric is not trapped in joints or the hub.

Step 8: Locking Main Joints

Details the process of locking the main pole joints by pushing them into place.

Step 9: Repeat Joint Locking

Repeats the joint locking procedure on the second main pole while supporting the central hub.

Step 10: Lock Remaining Poles

Step 11: Pegging Tri Guys

Unrolls the 'Tri Guys' from their pouches and pegs them out as shown for stability.

Step 13: Releasing Trapped Fabric

Step 14: Loosening Guy Rope

Step 15: Unfolding Pole Sections

Step 16: Locking Pole and Tightening Guy Rope

Locks the pole foot at position 'A' and tightens the guy rope at 'B' for support.

Step 18: Repeat Pole Locking

Tourer 400 Plus Telescopic Poles

Details extending telescopic lower poles on the Tourer 400Plus model for a smaller pack size.

Bedroom Section Assembly

Step 19: Assemble Bedroom Poles

Step 20: Thread Pole A

Step 21: Connect Angled Pole Sections

Tourer 400 Plus Bedroom Pole Fitting

Specific instructions for fitting shockcorded fiberglass bedroom poles on the Tourer 400Plus model.

Step 22: Attach Bedroom Pole Spike

Step 23: Secure Bedroom Pole Spike

Step 26: Peg Bedroom Section Loops

Step 27: Peg Main Corner and Vent Guys

Pegs the main corner and vent tri guy system into position on each side of the bedroom.

Balmoral Bedroom Pole Assembly

Balmoral Pole Construction

Details that Balmoral bedroom poles are steel and pre-formed, unlike aluminium poles.

Assemble Balmoral Poles

Guy Rope Positioning and Pegging

Step 28: Guy Rope Placement

Tri-Guy System Details

Step 29: Securing Tri-Guy Ropes

Unties tri-guy ropes from transit bags and pegs them out as far from the tent as possible.

Step 30: Pegging Bedroom Guy Ropes

Guy Rope Tensioning Advice

Recommends not to over-tension guy ropes to avoid distorting the tent shape; sufficient tension is key.

Step 31: Pegging Remaining Points

Inner Tent Fitting

Step 32: Lay Inner Tent Flat

Step 33: Clip Inner Tent Corners

Step 34: Clip Inner Tent Roof Hooks

Clips brass hooks on the inner tent to the rings in the roof of the bedroom section.

Tent Dismantling Procedure

Step 1: Prepare Inner Tents

Step 2: Remove Guy Ropes and Pegs

Step 3: Secure Guy Ropes

Step 4: Remove Bedroom Poles

Step 5: Prepare Main Dome

Step 6: Loosen Main Pole Joint

Loosens the main guy rope and joint collar to release tension and allow sliding.

Step 7: Fold Lower Pole Section

Step 8: Fold Lower Pole Inwards

Step 9: Repeat Pole Folding

Step 10: Secure Protective Bags

Step 11: Secure Auto Joint Covers

Step 12: Release Main Roof Joints

Releases the four main roof joints by pressing downwards and sliding the collar away.

Step 14: Secure Upper Protective Bags

Step 15: Fold Fabric into Rectangles

Step 16: Roll and Tie Fabric

Step 17: Pack Carry Bag

Important User Hints and Advice

Pole and Joint Durability

Explains the strength and materials of poles and joints, confirming their reliability and quality.

Pole and Joint Breakage

Addresses rare breakage, detailing replacement parts availability and warranty coverage.

Tent Water Resistance

Details fabric coating for water resistance and advises on seam sealing for untapped seams.

Pegging Safety Precautions

Condensation Management

Explains condensation causes and prevention methods like ensuring proper ventilation.

Preventing Fabric Damage

Damp Storage Warning

Cooking Indoors Safety

Prohibits cooking inside the tent due to synthetic fabrics melting and fire hazards.

Khyam HAREWOOD Specifications

General

Brand	Khyam
Model	HAREWOOD
Category	Tent
Language	English