KILL A WATT P4400 User Manual

P4400 Kill A Watt TM
Operation Manual
How to use the Kill-A-Watt meter:
a. Plug the meter into an electrical outlet
b. Plug device (computer, ipod, hair dryer) into meter
c. Manage the energy you measure (reduce, power down, or upgrade to energy efficient appliances)
Definitions:
kilo watt hour (kwh) = electricity consumed
watt = electricity demand or rate at which electricty is consumed
cost = number of kwh x cost per kwh (see your hydro bill for current utility rate)
The LCD shows all meter readings: Volts, Current, Watts, Frequency, Power Factor, and VA. The unit will start to accumulate KWH and
powered duration time (hour) after power is applied.
Press Volt Key for true RMS Voltage (Volts) display.
Press Amp Key for true RMS output current (Amps) display.
The Watt/VA Key is a toggle function key. Press the Watt/VA key once to display Watt meter, then press key to display VA meter. The LCD
will display Watts as the active power, where VA is the apparent Power. (VA=Vrms Arms)
The HZ/PF is a toggle function key. Press the HZ/PF key once to display the frequency (Hertz), then press key to display the Power Factor. HZ
is the frequency of output Voltage, where PF is the Power Factor (PF=W/Vrms Arms).
The KWH/Hour is a toggle function key. Press the KWH/Hour key once to show the cumulative energy consumption since power was ap
plied to the unit. Then press key to display the cumulative time since power was applied to the unit.
Consumption will be displayed in Kilowatt-Hours (from 0.01 KWH to 9999 KWH). Time will initially be displayed as Hours:Minutes
(from 00:00) and switch to Hours (to 9999). Counters will recycle to zero when they reach their maximum. To reset, remove power from
unit momentarily.
WARNING: Do not exceed maximum ratings as detailed on label.
1.
2.
3.
4.
5.
6.
7.
The Kill-A-Watt meter is a registered patent of P3
International.
If you experience difficulty in the operation of your unit, or if
your unit requires repair please contact:
P3 INTERNATIONAL CORPORATION
TECHNICAL SUPPORT
Email: techsupport@p3international.com
Additional information on UBC’s energy programs can be found
online at: sustain.ubc.ca/energy.html
These meters have been made avaliable for use through a collaboration of The UBC Sustainability Office and The UBC Library.
For more information on the Sustainability Office please visit: sustain.ubc.ca for the Library go to: library.ubc.ca
If this device is damaged there will be a $60.00
replacement fee. If the device is lost or stolen the fee
will be $73.00 for the replacement of the device and
the carrying case.

KILL A WATT P4400 Specifications

General

Model	P4400
Category	Test Equipment
Type	Power Meter
Operating Voltage	115 VAC
Maximum Load	15A
Current Range	0-15A
Maximum Amps	15A
Maximum Watts	1875 W
Energy Measurement	0-9999KWh
Frequency Display	Yes
Voltage Accuracy	±1%
Current Accuracy	±1%
Power Accuracy	±1%
Frequency Accuracy	±0.5Hz
Accuracy	±1%
Display	LCD
Overload indication	Yes
Frequency	60 Hz

Summary

How to Use the Kill-A-Watt Meter

Plug Meter into Outlet

Connect the Kill-A-Watt meter to a standard electrical outlet.

Connect Device to Meter

Plug your electrical device into the Kill-A-Watt meter's socket.

Manage Energy Consumption

Use measured data to reduce power consumption or upgrade appliances.

Definitions

Meter Operation and Readings

LCD Display Overview

The LCD displays Volts, Current, Watts, Frequency, Power Factor, and VA, accumulating KWH and time.

Volt Key Function

Press the Volt key to view the true RMS Voltage (Volts) display.

Amp Key Function

Press the Amp key to view the true RMS output current (Amps) display.

Watt/VA Key Function

Toggle between Watt (active power) and VA (apparent power) displays using the Watt/VA key.

HZ/PF Key Function

Toggle between Hertz (frequency) and Power Factor (PF) displays using the HZ/PF key.

KWH/Hour Key Function

Toggle between cumulative KWH consumption and time since power application.

Consumption and Time Display

Displays KWH consumption and time; counters reset by removing power.

Important Warnings and Information

Maximum Ratings Warning

Do not exceed the maximum ratings specified on the device label.

Manufacturer Information

The Kill-A-Watt meter is a registered patent of P3 International Corporation.

Contact and Support

Contact P3 International for technical support, repairs, or inquiries.

UBC Energy Program Information

Find information on UBC's energy programs online at sustain.ubc.ca/energy.html.

Device Replacement Fees

Information on fees for damaged, lost, or stolen devices and carrying cases.

Meter Availability and Resources

Meters available via UBC Sustainability Office collaboration; visit sustain.ubc.ca for info.