Kinetico 2040s s with Overdrive User Manual

19
Model 2030s 2040s with
Overdrive
2040c with
Overdrive
2050s
2050c
(Europe
only)
2060s 2060s with
Overdrive
2100s 2100s with
Overdrive
2175s 4040s with
Overdrive
4050s
(Europe
Only)
4060s with
Overdrive-
Activated
Carbon
4060s with
Overdrive-
Macrolite
Certified flow rate
@ 15 psi (or less)
9 gpm
34.1 Lpm
11 gpm
41.6 Lpm
7 gpm
26.5 Lpm
11.6 gpm
43.9 Lpm
20.5 gpm
77.6 Lpm
11 gpm
45.4 Lpm
21 gpm
79.5 Lpm
16.4 gpm
62.1 Lpm
11 gpm
41.6 Lpm
6 gpm
22.7 Lpm
11 gpm
41.6 Lpm
10 gpm
37.9 Lpm
Peak flow rate @
30 psi (or less)
16.5 gpm
62.5 Lpm
15 gpm
56.7 Lpm
15 gpm
56.7 Lpm
30 gpm
113.5 Lpm
30 gpm
113.5 Lpm
19 gpm
71.9 Lpm
31 gpm
117.3 Lpm
22 gpm
83.2 Lpm
15 gpm
56.7 Lpm
15 gpm
56.7 Lpm
15 gpm
56.7 Lpm
15 gpm
56.7 Lpm
Resin per tank,
in cubic feet
0.47 0.4 0.4 0.7 0.7
1.5 1.5 2.25 Upper: 0.4
Resin
Lower: 0.4 Carb
Upper: 0.4 Resin
Lower: 0.4 Carb
Upper: 0.25
Carb
Lower: 0.7 Resin
Upper: 0.2
Macrolite
Lower: 0.7 Resin
Resin per tank, in liters
13.3 11.3 11.3 19.8 19.8 42.5 42.5 63.7 Upper: 11.3
Resin
Lower: 11.3 Carb
Upper: 11.3 Resin
Lower: 11.3 Carb
Upper: 7.1 Carb
Lower: 19.8 Resin
Upper: 5.7
Macrolite
Lower: 19.8
Resin
Capacity per cycle,
in grains @ salt used per
cycle setting pounds
7867 @ 1.8*
9802 @ 2.7
5222 @ 1.0* 5222 @ 1.0* 12,481 @ 2.7*
15,817 @ 4.0
12,481 @ 2.7*
15,817 @ 4.0
25,253 @ 5.5*
41,087 @ 10.0*
25,253 @ 5.5*
41,087 @ 10.0*
65,139 @ 15*
81,845 @ 30
4921 @ 1.0* 4921 @ 1.0* 13,715 @ 4.0 14,883 @ 4.4
Capacity per cycle, in
grams @ salt used per
cycle setting kilograms
509 @ 0.81*
635 @ 1.2
338 @ 0.45* 338 @ 0.45* 809 @ 1.23*
1025 @ 1.8
809 @ 1.23*
1025 @ 1.8
1636 @ 2.5*
2662 @ 4.5*
1636 @ 2.5*
2662 @ 4.5*
4221 @ 6.8*
5303 @ 13.6
319 @ 0.45* 319 @ 0.45* 889 @ 1.8 964 @ 2.0
Grains exchanged
per pound of salt used
4371 @ 1.8*
3630 @ 2.7
5222 @ 1.0* 5222 @ 1.0* 4623 @ 2.7*
3954 @ 4.0
4623 @ 2.7*
3954 @ 4.0
4591* @ 5.5*
4109* @ 10.0*
4591* @ 5.5*
4109* @ 10.0*
4343* @ 15.0*
2728 @ 30.0
4921 @ 1.0* 4921 @ 1.0* 3429 @ 4.0 3383 @ 4.4
Grains exchanged per
kilograms of salt used
628 @ 0.81*
529 @ 1.2
751 @ 0.450* 751 @ 0.450* 658 @ 1.23*
569 @ 1.8
658 @ 1.29*
569 @ 1.8
654 @ 2.5*
592 @ 4.5*
654 @ 2.5*
592 @ 4.5*
621 @ 6.8*
390 @ 13.6
709 @ 0.45* 709 @ 0.45* 494 @ 1.8 482 @ 2.0
Max. flow rate to drain
during regenerations
0.69 gpm
2.6 Lpm
1.5 gpm
5.7 Lpm
1.5 gpm
5.7 Lpm
2.5 gpm
9.5 Lpm
2.5 gpm
9.5 Lpm
3.3 gpm
12.5 Lpm
3.3 gpm
12.5 Lpm
4.8 gpm
18.2 Lpm
3.0 gpm
11.4 Lpm
3.0 gpm
11.4 Lpm
3.0 gpm
11.4 Lpm
3.0 gpm
11.4 Lpm
Min./Max. operating
pressure
103.4 - 861.9 kPa
15 - 125 psi
172.3 - 861.9 kPa
25 - 125 psi
103.4 - 861.9 kPa
15 - 125 psi
Min./Max. operating
temperature
2 - 49°C
35 - 120°F
Max. working
pressure in psi
861.9 kPa
125 psi
Kinetico Water Softeners (2030s, 2040s OD, 2040c OD, 2050s, 2050c, 2060s, 2060s
OD, 2100s, 2100s OD, 2175s, 4040s OD and 4060s OD with Macrolite or carbon)
are tested and certified by NSF International against the requirements of NSF/ANSI
Standard 44 and CSA B483.1 for softener performance and chemical reduction of barium and
radium 226/228. NSF International certifies our product performance and reviews our
manufacturing facility and procedures to assure product consistency and integrity. ey also
assure that our literature accurately reflects our product capabilities.
Certified Continuous Flow Rate as validated by NSF International represents continuous service
flow of water at 15 psi pressure drop and is not an indication of maximum flow rate or unit
limitation. U.S. Patents: 4,336,134; 4,579,242; 4,889,623; 4,972,877; 5,022,994; 5,490,932
ese products are not intended to be used for treating water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the system.

Kinetico 2040s s with Overdrive Specifications

General

Brand	Kinetico
Model	2040s s with Overdrive
Category	Water System
Language	English