Why is my King Industrial Sander motor not reaching full power?
If your King Industrial Sander's motor isn't reaching full power, it could be due to incorrect power wiring. Try replacing it with the correct size. Another cause might be overloading; in this case, reduce the sanding load.
Why is my King Industrial Sander motor overheating?
If your King Industrial Sander's motor is overheating, it could be dirty. Clean the motor. Alternatively, the motor could be damaged, requiring a check and repair.
What to do if my King Industrial Sander motor does not run?
If the motor of your King Industrial Sander does not run when you turn the power switch on, the switch may be burned out. Replace the switch. It's also possible that a connection wire is loose or damaged; in this case, tighten or replace the wire.
How to reduce excessive vibration on my King Industrial Sander?
If your King Industrial Sander has excessive machine vibration, it might be incorrectly leveled. Adjust the machine leveling.
Why King Industrial Sander motor does not run at full speed?
If your King Industrial Sander motor does not run at full speed, the power voltage may be too low. Test the voltage. It's also possible that the motor is damaged, so check and repair it.
What to do if my King Industrial Sander leaves mark on workpiece?
If your King Industrial Sander leaves marks on the workpiece, the sanding drum may be damaged. Replace it. Alternatively, the sanding sleeve on the drum might be worn in some areas, so replace the sanding sleeve.
Why is the sanding drum on my King Industrial Sander turning in the wrong direction?
If the sanding drum on your King Industrial Sander turns in the wrong direction, it could be due to the wrong phase or voltage. Make sure the phase and voltage comply with machine requirements.
How to prevent burns on workpiece with King Industrial Sander?
If your King Industrial Sander is causing burns on the workpiece, it could be due to using the wrong abrasive grit on the sanding sleeve. Try using a coarser grit to remove more material.
Keep dated proof of purchase for warranty and servicing purposes.
Replacement parts available at authorized King Canada service centres.
King Canada warrants product against defects in materials and workmanship for 2 years.
Manual is a guide only; specifications subject to change.
Refer to King Canada website for updated parts information.
Read manual, labels, learn applications, limitations, and hazards.
Ensure tool is properly grounded with a 3-conductor cord and plug.
Keep guards in good working order, properly adjusted and aligned.
Remove all tools from the machine before turning it on.
Cluttered areas and slippery floors invite accidents.
Do not use power tools in damp/wet locations or expose to rain.
Ensure all visitors stay a safe distance from the work area.
Secure workshop with padlocks, master switches, or by removing starter keys.
Operate tool at proper speed for better and safer job performance.
Do not force the tool or attachment for unintended jobs.
Avoid loose clothing, gloves, jewelry; use non-slip footwear and hair covering.
Wear safety glasses (ANSI Z87.1); use face/dust mask if needed.
Maintain proper footing and balance at all times.
Keep tools sharp and clean; follow lubrication instructions.
Disconnect power before servicing or changing accessories.
Ensure switch is "OFF" before plugging in.
Consult manual for accessories; use of improper ones may cause hazards.
Serious injury can occur if the tool tips over.
Check damaged guards/parts for proper operation before further use.
Turn power "OFF"; wait for complete stop before leaving.
Essential safety precautions specific to operating spindle sanders.
Identifies key components of the spindle sander with numbered labels.
Specifies the required power supply and circuit breaker for safe operation.
Details the importance and procedure for proper grounding to prevent shock.
Instructions for operating the sander on a 110V-120V circuit.
Instructions for converting and operating the sander on a 220V circuit.
Guidelines for selecting appropriate extension cords for the sander.
Instructions for unpacking and initial cleaning of the spindle sander.
Step-by-step guide for fitting sanding sleeves onto spindles and drums.
Procedure for securely attaching a spindle or drum to the oscillating spindle.
Guide on selecting and fitting table inserts based on spindle diameter.
Details which table inserts to use for different spindle/drum sizes.
Instructions on how to adjust and lock the table tilt angle.
Procedure to ensure the table is perpendicular to the spindle.
How to safely start and stop the spindle sander using the safety switch.
Information on connecting the sander to a dust collector for dust management.
Step-by-step guide for performing sanding operations with the machine.
Procedures for cleaning, waxing the table, and lubricating parts.
Lists common problems and their solutions for the spindle sander.
General| Model | KC-OVS-FX3 |
|---|---|
| Table Tilt | 0 - 45 degrees |
| Category | Sander |
| Type | Oscillating |
| Spindle Stroke | 3/4 inch |
| Spindle Sizes | 1/2, 3/4, 1, 1-1/2, 2, 3 inches |
| Voltage | 110V |
To Next Page
