EasyManua.ls Logo

KitchenAid KUDC10FXSS2 - Grounding Instructions; For a grounded, cord-connected dishwasher; For a permanently connected dishwasher

KitchenAid KUDC10FXSS2
52 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
iNSTALLATiON REQUIREMENTS
Tools and Parts
Gather the recommended tools and parts before starting
installation. Read and follow the instructions provided with
any tools listed here.
All Installations
Tools needed:
_,. _ z_..--_ Flat-blade
r,,ers I screwdriver
5 1
_e and ¼ _,,_ UL L sted/CSA
nut drivers or _Jf Approved twist-on _
hex sockets _ wire connectors* v
10" adjustable wrench_ %" chert-end
that opens to _f_'-_' wrench _f-_-_'_
1 "
1V_ (2.9 cm) _.
If installing custom front panels, ..._-J
Torx ®tT15 screwdriver
-Must be the proper size to connect _'our household wiring
to 16-gauge wiring in dishwasher
Other useful items you may need:
F ash ight _ Batht0we _
Parts supplied:
Drain hose Drain hose #10 x 1/2"
(lalampS(a2)nd ,_ Pehia_ps-
lsma _ _ screws (2)
2 - under-
counter
mounting
brackets (top)
Parts needed:
3 " 3 " " "
Comprx 3A hosefittLng
For part or k!t, see local
retailer or call Whirlpool
Parts: 1-800_442'9991. Part
Number WI0273460
4 #10 x 1/2"wood screws (if installing custom front panels)
Supplied in Kit:
4 Plastic studs (attached to each other by runners)
4 Short screws (10-16 hex head screw)
4 Long screws (8-18 Torx ®thead screws)
1 Template (located inside Use and Care Guide bag
assembly)
1 Instruction sheet (located inside Use and Care Guide bag
assembly)
NOTE: The screws supplied are used for only 3/4"thick
wooden panel. If the wooden panel is less than 3/4"thick,
customer must purchase screws locally.
Other parts you may also need:
1V2 -2 Masking or Moisture
(3.81-5 cm)duct tape barrier tape J_,_
screw4ype i i (Part Number/_/
clamps(3 maximum)[ ] 4396277)i
NOTE: Moisture barrier tape is recommended when installing a
dishwasher under a wood countertop.
NOTE: Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See
"Electrical Requirements" section. It is recommended that
electrical connections be made by a licensed electrical installer.
In addition, for first=time installations
Tools needed:
Cordless drill
with 1/2";¾"
and 11/2'' hole
saw bits
Parts needed:
Copper tubing (%" see "Electrical Requirements,, SeCtion:
O.D.suggested)0r
flexible braided For Direct wire: For Pewer supply
Watersuauv ne use UL Listed/ Cord: useUL
CSA Approved Listed/CSA
_,,f'--_._,_\ I strain _elief Approved power
(.[.[._\_-_ _)_9.)))_ to fit% (2.2cm) supp!yCord kit
marked for uSe With
dishWaSher
Additional parts supplied with top-venting models only:
2#8xlY8 TorX T15screwS 4#!0x y8 hex-head screws
Additional parts supplied with certain models only:
i B0tt0m sound pad
(located in lower rack) J
Make sure all these parts are included in the literature package.
If parts are not included, call 1-800-422-1230.
TORX is a registered trademark of Saturn Fasteners, Inc.
3

Other manuals for KitchenAid KUDC10FXSS2

Related product manuals