12
Option Selections
You can customize your cycles by pressing the options desired. If
you change your mind, press the option again to turn off the
option. Select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press HEAT DRY anytime before
drying begins.
Press START/RESUME to repeat the same cycle and options as in
the previous wash cycle.
NOTE: If the last cycle you completed was a rinse cycle, when
you press Start/Resume, the dishwasher runs the last full wash
cycle and options.
Hi-Temp Scrub
Select this option to heat the water during parts of the cycle, and
add a rinse. Higher water temperatures and an extra rinse help
clean tough soils. Hi-Temp Scrub, with the Heavy Duty cycle,
heats the water in the main wash and the prewash. Hi-Temp
Scrub, with the Normal cycle, raises the water temperature in the
main wash.
This option adds heat, water, and wash time to a cycle.
NOTE: Hi-Temp Scrub is an option with the Heavy Duty and
Normal cycles.
Sani Rinse
Select this option to raise the water temperature in the final rinse
to approximately 155°F (68°C). The Sani Rinse option adds heat
and time to the cycle. This high temperature rinse sanitizes your
dishes and glassware in accordance with NSF/ANSI Standard 184
for Residential Dishwashers. Certified residential dishwashers are
not intended for licensed food establishments.
NOTE: Sani Rinse is an option with the Heavy Duty and Normal
cycles. Only these sanitization cycles have been designed to meet
the NSF/ANSI requirements.
Heat Dry
The Heat Dry option in combination with rinse aid will give you
excellent drying results. The energy to use Heat Dry costs pennies
per cycle. Heat Dry is on when the light is lit on the Heat Dry
button. Be sure to load plastic items in the upper rack to avoid
damage.
You may turn off the Heat Dry option by pressing HEAT DRY so
that the light goes off. However, you will have items in your dish
load that will not be dry at the end of the cycle.
NOTE: The Heat Dry option is used in all cycles except Rinse
Only.
Control Lock
Use Control Lock to avoid unintended use of your dishwasher.
You can also use the control lock feature to avoid unintended
cycle or option changes during a cycle.
When Control Lock is lit, all buttons are disabled.
NOTES:
■ The dishwasher door can be opened while the controls are
locked.
■ You can turn on the lock while the dishwasher is running.
To turn on the lock
Press and hold HEAT DRY for 5 seconds. The Control Lock light
glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
To turn off the lock
Press and hold HEAT DRY for 5 seconds. The Control Lock light
turns off.
4 Hour Delay
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay countdown. (See “Adding Items During a Cycle.”) The delay
countdown will not continue if the door is not closed firmly.
To delay the start (Models KUDP02IR, KUDP02CR)
1. Close the door.
2. Select a wash cycle and options. The selected cycle and
option lights will glow.
3. Press 4 HOUR DELAY. The 4 Hour Delay light will glow.
4. Press START/RESUME.
NOTE: To cancel the delay, press 4 HOUR DELAY. To immediately
start your dishwasher, press START/RESUME.
To delay the start (Model KUDP02SR)
1. Open the door.
2. Select a wash cycle and options. The selected cycle and
option lights will glow.
3. Press 4 HOUR DELAY.
You will see
showing in the display. The 4 Hour Delay light will glow.
4. Close the door firmly.
5. Press START/RESUME. The Start/Resume light will glow.
NOTE: To cancel the delay, open the door and press 4 HOUR
DELAY. To immediately start your dishwasher, press START/
RESUME.
To delay the start (Models KUDP02FR, KUDP02FSPA)
1. Open the door.
2. Select a wash cycle and options. The selected cycle and
option lights will glow.
3. Press 4 HOUR DELAY. The 4 Hour Delay light will glow.
4. Press START/RESUME.
5. Close the door firmly within 3 seconds of pressing Start/
Resume.
NOTE: To cancel the delay, open the door and press 4 HOUR
DELAY. To immediately start your dishwasher, press START/
RESUME and close the door firmly.
Status Indicators
Clean
The Clean light glows when a cycle is finished. The light turns off
when you open and close the door or press CANCEL.
Sanitized
If you select the Sani Rinse option, Sanitized light glows when the
Sani Rinse cycle is finished. If your dishwasher did not properly
sanitize your dishes, the light flashes at the end of the cycle. This
can happen if the cycle is interrupted. The light goes off when you
open and close the door or press CANCEL.
To Next Page
Loading...
Need help?
General
