4. Add Rinse Aid
■ Your dishwasher is designed to use rinse aid for good drying
performance. Without rinse aid, your dishes and dishwasher interior
will have excessive moisture. The heat dry option will not perform
as well without rinse aid.
■ Rinse aid keeps water from forming droplets that can
dry as spots or streaks. It also improves drying by
allowing water to drain off of dishes after final rinse.
■ To add rinse aid, turn the
dispenser cap to “Refill” and lift
off. Pour rinse aid into the
opening until indicator level is at
“Full.” Replace dispenser cap
and turn to “Lock.” Make sure
cap is fully locked.
NOTE: For most water conditions,
the factory setting will give good
results.
■ Check water hardness level to ensure no rings
or spots on your dishware before adding rinse
aid or adjusting the factory setting.
■ If you are experiencing poor drying
performance, you may want to try a higher
setting.
Turn the arrow adjuster inside the dispenser to
change rinse aid setting.
5. Select a Cycle (cycles vary by model)
Efficient dishwashers run longer to save water and energy, just as
driving a car slower saves on gas. Typical cycle time is approximately
2¹⁄₂ hours, but can take less or more time to complete depending on
selections.
6. Select Options (options vary by model)
You can customize your cycles by pressing the options desired. If you
change your mind, press the option again to turn off the option. Not all
options are available for every cycle. If an invalid option is selected for a
given cycle, the lights will flash.
7. Start or Resume a Cycle
NOTE: Run hot water at sink nearest your dishwasher until water is hot.
Turn off water.
■ If Start/Resume button is located on top of door, push door firmly
closed within 3 seconds of pressing START/RESUME. If door is not
closed within 3 seconds, the Start button LED will flash, an audible
tone will be heard, and cycle will not start.
IMPORTANT: If anyone opens the door (such as, for adding a dish,
even during the Delay Hours option), Start/Resume button must be
pressed each time.
■ If Start/Resume button is located on front of door, push door firmly
closed. The door latches automatically. Select the wash cycle,
options and press START/RESUME or press START/RESUME to
repeat the same cycle and options as in previous wash cycle.
This information covers several different models. Your dishwasher may not have all of the cycles and options described.
RINSE AID
IMPROVES DRYING
CHECK
WITH DOOR
FULLY OPEN
Full
Add
Lock
CYCLES SOIL LEVEL WASH TIME* (MINS.)
W/O OPTIONS
WATER
USAGE
GALLONS
(LITERS)
TYPICAL MAX
The most advanced and versatile cycle. ProWash™ cycle
senses the load size, soil amount, and toughness of soil, to
adjust the cycle for optimal cleaning using only the amount of
water and energy needed.
Light to Medium 110 150 3.8 (14.5)
Tough/Baked-On 125 190 5.0 (19.1)
Heavy 125 190 7.7 (29.0)
Use for hard-to-clean, heavily soiled pots, pans, casseroles,
and regular tableware.
Heavy/Baked-On 140 205 7.9 (30.0)
This cycle is recommended to completely wash a full load of
normally soiled dishes. Selecting this cycle will default to the
options recommended for normal amounts of food soil. The
energy label is based on this cycle.
Light 110 150 2.8 (10.5)
Medium 110 150 4.0 (15.0)
Heavy 125 190 7.9 (30.0)
Use for lightly soiled items or china and crystal. Light to Medium 105 145 4.2 (15.2)
Heavy/Baked-On 120 185 7.7 (29.0)
When you need fast results, the Express Wash will clean
dishes using slightly more water and energy. Select the Heat
Dry or ProDry™ option to speed drying times.
All soil levels 58 64 6.2 (23.5)
Use for rinsing dishes, glasses, and silverware that will not be
washed right away.
Do not use detergent.
All soil levels 17 20 2.4 (9.0)
To Next Page
Loading...
Need help?
General
