Klark Teknik DN200 User Manual

Quick Start Guide
DN200
2-Channel Active DI Box with Extended Dynamic Range and Sum/Split Options
V 1.0
(EN) Controls
(1) STEREO INPUT – Connect a line-level audio source via stereo
⁄" TRS cable. Ensure that the L/R INPUTS and LINK THRU jacks
are disconnected when using the STEREO INPUT jack.
(2) PAD – Press to reduce the input signal by 20 dB for use with
hot signals.
(3) EARTH – Press to separate the input and output grounds,
potentially eliminating earth/ground loops between
equipment on dierent mains supplies.
(4) L/R INPUT – Connect either balanced or unbalanced XLR
or ¼" cables. Ensure that the ⁄" STEREO INPUT jack is
disconnected when using these inputs.
(5) 48 V LED – Lights when the unit receives sucient
phantom power. Note that the DN200 must be powered
to operate correctly.
Important: Although the DN200 will function as a mono
device when only one channel is connected, both channels
should be powered to use stereo, split, or sum modes.
(6) SUM – When engaged, the left and right inputs are summed
and fed to the left and right outputs. Note that phantom
power must be delivered to both output connections for
dual-output operation.
(7) SPLIT – When engaged, the left input is fed to the left and
right outputs. Note that phantom power must be delivered
to both output connections for dual-output operation.
(8) L/R OUTPUT – Send the signals to a mixer or recording
interface via balanced XLR cables. Note that the connected
device must be able to provide +48 V phantom power to
these connectors.
(9) LINK THRU – Send the signals to an alternate source via
balanced or unbalanced ¼" cables. Ensure that the ⁄" STEREO
INPUT jack is disconnected when using these outputs.
(2) (3)
(7)(6)
(8) (9)
(1)
(5)
(4)

Klark Teknik DN200 Specifications

General

Channels	2
Ground Lift	Yes
Dynamic Range	> 100 dB
Input Connectors	XLR
Output Connectors	XLR
THD+N	<0.005%
Input Impedance	1 MΩ
Output Impedance	50 Ω
Frequency Response	20 Hz to 20 kHz
Power Supply	12 V DC

Summary

DN200 Controls

STEREO INPUT

Connect a line-level audio source via 1/8" TRS cable. Ensure other inputs are disconnected.

PAD

Reduces input signal by 20 dB for use with hot signals.

EARTH

Separates input/output grounds to eliminate ground loops between equipment.

L/R INPUT

Connect balanced/unbalanced XLR or 1/4" cables. Ensure 1/8" STEREO INPUT is disconnected.

48 V LED

Indicates sufficient phantom power. Unit must be powered to operate correctly.

SUM

Sums left/right inputs to left/right outputs. Phantom power required for dual-output.

SPLIT

Feeds left input to left/right outputs. Phantom power required for dual-output.

L/R OUTPUT

Sends signals to mixer/interface via balanced XLR. Requires +48V phantom power.

LINK THRU

Sends signals to alternate source via 1/4" cables. Ensure 1/8" STEREO INPUT is disconnected.

DN200 Specifications

Specifications - Inputs

Details on input connectors, impedance, and maximum input level.

Specifications - Outputs

Details on output connectors, impedance, maximum output level, and minimum load.

Specifications - System

Details on noise, frequency response, distortion, and crosstalk.

Specifications - Power Requirement

Details on voltage and current consumption for operation.

Specifications - Physical

Details on device dimensions and weight.

Legal Disclaimers and Warranties

Legal Disclaimer

Statement regarding liability for reliance on document contents and trademark ownership.

Limited Warranty

Information on applicable warranty terms and conditions.

Compliance and Contact Information

FCC Compliance Information

Details on FCC compliance, interference, and operation conditions for the DN200.

EU Representative and Declaration

Information on EU compliance directives and the EU representative.