Why does my Kogan Washer/Dryer take so long to drain?
If your Kogan Washer/Dryer is taking too long to drain, first check the drain hose to ensure it is not squashed or kinked. Additionally, the drain pump filter might be blocked, so clean the filter. Also, inspect the drainage system pipes for any blockages and clean them if necessary.
What to do if the motor of my Kogan KAGWAS10D6A Washer/Dryer does not work?
If the motor in your Kogan Washer/Dryer isn't working, start by checking the connection between the motor and the wire to ensure it's secure. Also, the motor’s overheat protection might have been enabled. In this case, check if the machine is overloaded, switch it off, and try again once the motor cools down.
Why does my Kogan KAGWAS10D6A take so long to fill?
If your Kogan Washer/Dryer is taking too long to fill, make sure the water tap is fully open. Also, verify that the drain hose is properly connected. If these steps don't resolve the issue, the water inlet valve may be damaged, and you should contact Kogan.com.
What to do if my Kogan KAGWAS10D6A Washer/Dryer overflows?
If your Kogan Washer/Dryer is overflowing or the water sensor is malfunctioning, the water inlet valve may be damaged and needs replacement. Check the connection between the water sensor and the wire to ensure it is secure. If the problem persists, the water sensor might be damaged, and you should contact Kogan.com.
What to do if the door lock alarm sounds on my Kogan KAGWAS10D6A?
If the door lock alarm sounds on your Kogan Washer/Dryer, make sure the door is securely locked. Also, check if any garment is caught between the door and the seal, and if so, put the garment into the drum. If the issue continues, the door lock may be damaged, and you should contact Kogan.com.
What causes a heating tube fault in my Kogan Washer/Dryer?
If there is a heating tube fault in your Kogan Washer/Dryer, check the connection between the heating tube and the wire to ensure it is secure. If the problem persists, the heating tube might be damaged, and you should contact Kogan.com.
Why does the inverter fail to start in my Kogan KAGWAS10D6A?
If the inverter fails to start in your Kogan Washer/Dryer, check the connection between the inverter and the wire to ensure it is secure. If the issue persists, the inverter may be damaged, and you should contact Kogan.com.
How to fix a temperature sensor fault in my Kogan Washer/Dryer?
If there is a temperature sensor fault in your Kogan Washer/Dryer, check the connection between the wire and the temperature sensor to ensure it is secure. If the problem continues, the temperature sensor may be damaged, and you should contact Kogan.com.
How to decrease the cooling time of my Kogan KAGWAS10D6A Washer/Dryer?
To address excessive cooling time with your Kogan Washer/Dryer, ensure that the tap is open and that the water is cold.
General| Model | KAGWAS10D6A |
|---|---|
| Type | Washer/Dryer Combo |
| Washing Capacity | 10 kg |
| Drying Capacity | 6 kg |
| Energy Rating | 4 Stars |
| Spin Speed | 1400 RPM |
| Color | White |
| Voltage | 220-240V |
| Frequency | 50 Hz |
| Water Pressure | 0.03-1MPa |
| Wash Programs | 16 |
| Dimensions (H x W x D) | 85cm x 60cm x 60cm |
Read and understand thoroughly these safety instructions before use. Kogan.com cannot be held liable for damage caused by non-compliance.
Ensures electrical safety by proper connection and effective earthing system compliance with regulations.
Guidelines for proper installation and operation to avoid damage and ensure longevity.
Precautions to ensure children's safety around the appliance and its operation.
Diagrams illustrating and labeling the external and internal components of the washer-dryer.
Instructions for unpacking the machine and a list of all supplied accessories.
Guidance on how to safely remove transit bolts before operation and their importance for transport.
Recommendations for placing the washer-dryer on a stable surface with adequate spacing from walls.
Instructions on how to adjust the machine's feet for stable and proper operation, preventing vibration.
Detailed steps for correctly connecting the drain hose to a sink or standpipe for efficient drainage.
Instructions for connecting the water inlet hose to the tap and the machine's inlet valve.
Detailed explanation of each button on the control panel: Start/Pause, Dry, Temp, Speed, Rinse+, Knob.
Instructions for enabling/disabling the child lock and muting operational tones for user convenience.
Explanation of digital display icons, including time, delay, child lock, door lock, and cycle status indicators.
Comprehensive chart detailing wash programs, weight capacity, time, temperature, rinse, spin speed, and dry time.
Guide for preparing the washer for its first use, including running a cycle without clothes.
Instructions on how to properly load laundry into the drum and add detergent and fabric softener to the correct compartments.
A sequential guide covering turning on the tap, connecting power, loading, selecting programs, and starting the wash cycle.
Visual guide to washing programs, their symbols, and the types of fabrics they are suitable for.
Explanation of the door lock function and important tips for washing and drying processes.
Instructions for cleaning the machine's exterior surfaces and the washing drum to maintain hygiene.
Steps for cleaning the drawer housing and the water inlet filter, ensuring proper water flow.
Detailed instructions on how to safely clean the drain pump filter, including frequency and error codes.
Key technical details of the washer-dryer, including capacity, power, dimensions, and weight.
Information regarding responsible disposal of the appliance to prevent environmental harm.
A guide to identifying and resolving common operational problems with error codes, causes, and solutions.
To Next Page
